|
|
|
|
MIB Information: hdr2Cfg
1.3.6.1.4.1.429.4.48.1
MIB Information: hdr2CfgTable
1.3.6.1.4.1.429.4.48.1.1
not-accessible
Description: A table containing the configuration parameters for the Hiper E1/R2 Card.
MIB Information: hdr2CfgEntry
1.3.6.1.4.1.429.4.48.1.1.1
not-accessible
Description: Configuration parameters for the E1/R2 module.
MIB Information: hdr2CfgIndex
1.3.6.1.4.1.429.4.48.1.1.1.1
mandatory read-only
Description: The index which uniquely identifies the Hiper E1/R2 CARD to which this entry is applicable.
Settings: INTEGER
MIB Information: hdr2CfgRegSigType
1.3.6.1.4.1.429.4.48.1.1.1.2
mandatory read-write
Description: This object Defines the type of Register Signaling used for Bit Oriented Signaling.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = r2MFC
(2) = r2MFSC
MIB Information: hdr2CfgAnumIden
1.3.6.1.4.1.429.4.48.1.1.1.3
mandatory read-write
Description: This parameter enables or disables the collection of calling party ( A party or ANI) phone numbers when used with R2MFC signaling type.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: hdr2CfgForcedRel
1.3.6.1.4.1.429.4.48.1.1.1.4
mandatory read-write
Description: In E1/ R2 Forced Release Line signal will be sent only in case of this parameter is enabled. This signal is optional.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: hdr2CfgLastBDigTout
1.3.6.1.4.1.429.4.48.1.1.1.5
mandatory read-write
Description: This parameter decides after how many milliseconds of silence during the B digit reception the B party number is assumed as completed.
Settings: INTEGER
Syntax Ref. Type: RANGE
100 = 10000
MIB Information: hdr2CfgAddrComplete
1.3.6.1.4.1.429.4.48.1.1.1.6
mandatory read-write
Description: On reception of this signal it is assumed that the required number of B party digits are received. It can hold the values ranging from A1 to A15. It depends on country specification.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = a3
(2) = a5
(3) = a6
MIB Information: hdr2CfgEndBparty
1.3.6.1.4.1.429.4.48.1.1.1.7
mandatory read-write
Description: This indicates whether I15 is will be received as an indication for End of B party number or not. If enabled at the end of B party number this I15 signal is received informing that B party number is completed.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: hdr2CfgAlawMulaw
1.3.6.1.4.1.429.4.48.1.1.1.8
mandatory read-write
Description: This object is configuration to apply A Law(E1) or MuLaw(T1) Companding.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = aLAW
(2) = mULAW
(3) = auto
MIB Information: hdr2CfgLineSigType
1.3.6.1.4.1.429.4.48.1.1.1.9
mandatory read-write
Description: This object defines the type of Line Signaling for Bit Oriented Signaling.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = r2DIG
(2) = p7DIG
(3) = r2EandM
MIB Information: hdr2CfgProjID
1.3.6.1.4.1.429.4.48.1.1.1.10
mandatory read-write
Description: Depending on this parameter country dependent or project dependent parameters are updated. Each and every parameter has a set of variables to be initialized.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = iTU-T
(2) = argentina
(3) = australia
(4) = brazil
(5) = chile
(6) = china
(7) = colombia
(8) = india
(9) = korea
(10) = malaysia
(11) = mexico
(12) = newZealand
(13) = philippines
(14) = sweden
(15) = venezuela
MIB Information: hdr2CfgSeizeAck
1.3.6.1.4.1.429.4.48.1.1.1.11
mandatory read-write
Description: It defines whether seize acknowledge signal is used or not for Bit Oriented Signaling.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: hdr2CfgAnumBnum
1.3.6.1.4.1.429.4.48.1.1.1.12
mandatory read-write
Description: During Bit oriented Register Signaling after number of B party ( called party or DNIS) digits have been received the A party (calling or ANI) digits are requested provided A party (ANI) request is enabled. Otherwise this parameter is ignored.
Settings: INTEGER
Syntax Ref. Type: RANGE
1 = 36
MIB Information: hdr2CfgSubBusy
1.3.6.1.4.1.429.4.48.1.1.1.13
mandatory read-write
Description: This object is used in case of subscirber busy.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = b2
(2) = b3
MIB Information: hdr2CfgSndCallingPtyCatgy
1.3.6.1.4.1.429.4.48.1.1.1.14
mandatory read-write
Description: This register Signal requests the calling ( A PARTY's ) category.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = a5
(2) = a6
MIB Information: hdr2CfgLineDirection
1.3.6.1.4.1.429.4.48.1.1.1.15
mandatory read-write
Description: This object sets the direction of the channels on the span line.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = incoming
(2) = outgoing
(3) = both
MIB Information: hdr2CfgPersistentOverride
1.3.6.1.4.1.429.4.48.1.1.1.16
mandatory read-write
Description: This object allows the recieved line signal persistence (debounce time).
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 255
MIB Information: hdr2CfgWrongNumber
1.3.6.1.4.1.429.4.48.1.1.1.17
mandatory read-write
Description: This object is the backward register signal used to indicate that an invalid number has been dialed.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = b5
(2) = b7
MIB Information: hdr2CfgIncomingCpc
1.3.6.1.4.1.429.4.48.1.1.1.18
mandatory read-write
Description: This object determines the default calling party category to be assumed when none is supplied for an incoming call.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = analog
(2) = digital
(3) = maintanace
(4) = test
MIB Information: hdr2CfgRegSigStatus
1.3.6.1.4.1.429.4.48.1.1.1.19
mandatory read-write
Description: This object determines whether or not register signalling is used for incoming and outgoing calls for R2.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: hdr2CfgUnusedAbcd
1.3.6.1.4.1.429.4.48.1.1.1.20
mandatory read-write
Description: This object determines the bit pattern transmitted for whichever of the ABCD bits are not used for the selected line signalling scheme. This means CD for R2 Digital and P7 and BCD for R2 E&M.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 15
MIB Information: hdr2CfgBlkToBlk
1.3.6.1.4.1.429.4.48.1.1.1.21
mandatory read-write
Description: This object determines whether or not a blocking signals received in the idle state is automatically responded to with a transmitted block signals.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: hdr2CfgDelayLos
1.3.6.1.4.1.429.4.48.1.1.1.22
mandatory read-write
Description: This object determines the required duration of the LOS state before active calls are dropped and the signalling is reinitialised. Restoration of signal during this period allows calls to continue.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 10000
MIB Information: hdr2CfgInGlare
1.3.6.1.4.1.429.4.48.1.1.1.23
mandatory read-write
Description: This object determines whether the incoming call is accepted and the outgoing call is dropped in a glare condition or both calls are dropped as currently implemented.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: hdr2CfgClrCall
1.3.6.1.4.1.429.4.48.1.1.1.24
mandatory read-write
Description: This object determines whether an active call is cleared when an unexpected line signal is received or the line signal is ignored as currently implemented.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: hdr2CfgANumQry
1.3.6.1.4.1.429.4.48.1.1.1.25
mandatory read-write
Description: This object determines whether or not an extra MFC cycle is used before to the A-number to indicate whether an A-number is availableusing III-1 for yes and III-0 for no.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: hdr2CfgANumNAv
1.3.6.1.4.1.429.4.48.1.1.1.26
mandatory read-write
Description: THis object interpret I-12 as A-number not available.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: hdr2CfgANumReq
1.3.6.1.4.1.429.4.48.1.1.1.27
mandatory read-write
Description: this object backward register signal used to request transmission of the next A-number digit Frequently this is the same as the signal used to request transmission of the call category and A-number .
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = c1
(2) = c5
(3) = c6
(4) = c9
MIB Information: hdr2CfgClrFwd
1.3.6.1.4.1.429.4.48.1.1.1.28
mandatory read-write
Description: This object repeatd size/clear-forward sequence is sent to startup to try to provoke a response from attached equipment.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: hdr2CfgRelGuard
1.3.6.1.4.1.429.4.48.1.1.1.29
mandatory read-write
Description: This object is duration for which Release Guard signal is sent.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 2000
MIB Information: hdr2CfgPIClrBck
1.3.6.1.4.1.429.4.48.1.1.1.30
mandatory read-write
Description: This object determines whether or not a repeated release/Seize-ack sequence is sent while attempting to clear anincoming call.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: hdr2CfgDelayAns
1.3.6.1.4.1.429.4.48.1.1.1.31
mandatory read-write
Description: this object determines the delay between the end of addressing and transmission of the answer signal.
Settings: INTEGER
Syntax Ref. Type: RANGE
100 = 2000
MIB Information: hdr2CfgBNumLen
1.3.6.1.4.1.429.4.48.1.1.1.32
mandatory read-write
Description: this object determines the number of B-number digits to accept beore sending the 'address complete'signal provided the 'end of B_number'signal is not received first.
Settings: INTEGER
Syntax Ref. Type: RANGE
1 = 36
MIB Information: hdr2CfgActBTout
1.3.6.1.4.1.429.4.48.1.1.1.33
mandatory read-write
Description: this object determines action to be taken on last B-digit timeout.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = b-number
(2) = error
MIB Information: hdr2CfgInSubFree
1.3.6.1.4.1.429.4.48.1.1.1.34
mandatory read-write
Description: this object backward register signal used to indicate acceptance of an incoming call.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = b1
(2) = b5
(3) = b6
MIB Information: hdr2CfgBNumNFnd
1.3.6.1.4.1.429.4.48.1.1.1.35
mandatory read-write
Description: this object determines the action on B-Number not found in teh DNIS handling table.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = acceptAllCalls
(2) = rejectAllCalls
(3) = acceptAllCallsAsDigital
(4) = acceptAllCallsAnalog
MIB Information: hdr2CfgSndBNumN
1.3.6.1.4.1.429.4.48.1.1.1.36
mandatory read-write
Description: this object backward signal requesting retransmission of curent B-number digit for outgoing calls.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = a9
(2) = a10
MIB Information: hdr2CfgSndBNumN1
1.3.6.1.4.1.429.4.48.1.1.1.37
mandatory read-write
Description: this object backward signal requesting transmission of B-number digit N-1 for outgoing calls.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = a2
(2) = a8
(3) = a9
(4) = a10
MIB Information: hdr2CfgSndBNumN2
1.3.6.1.4.1.429.4.48.1.1.1.38
mandatory read-write
Description: this object backward signal requesting transimission of B-number digit N-2 for outgoing calls.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = a7
(2) = a9
MIB Information: hdr2CfgSndBNumN3
1.3.6.1.4.1.429.4.48.1.1.1.39
mandatory read-write
Description: this object backward signal requesting transimission of B-number digit N-3 for outgoing calls.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = a8
(2) = a10
MIB Information: hdr2CfgSndFBNum
1.3.6.1.4.1.429.4.48.1.1.1.40
mandatory read-write
Description: this object determines whether or not the I-15 'end of B-number' signal is used for outgoing calls.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = a2
(2) = a9
(3) = a10
MIB Information: hdr2CfgDumANum
1.3.6.1.4.1.429.4.48.1.1.1.41
mandatory read-write
Description: this object default A-number for outgoing calls in case none is supplied during call initiation.
Settings: DisplayString
Syntax Ref. Type: SIZE
1 = 36
MIB Information: hdr2CfgEndANum
1.3.6.1.4.1.429.4.48.1.1.1.42
mandatory read-write
Description: This object forward register signal used to indicate that no more a_number digits are avaible.default=iii-15.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = iii-12
(2) = iii-15
MIB Information: hdr2CfgOutCatAnalog
1.3.6.1.4.1.429.4.48.1.1.1.43
mandatory read-write
Description: This object forward signals used to indicate the call category for outgoing calls.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = ii-1
(2) = ii-2
(3) = ii-3
(4) = ii-4
(5) = ii-5
(6) = ii-6
(7) = ii-7
(8) = ii-8
(9) = ii-9
(10) = ii-10
(11) = ii-11
(12) = ii-12
(13) = ii-13
(14) = ii-14
(15) = ii-15
MIB Information: hdr2CfgOutCatDigital
1.3.6.1.4.1.429.4.48.1.1.1.44
mandatory read-write
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = ii-1
(2) = ii-2
(3) = ii-3
(4) = ii-4
(5) = ii-5
(6) = ii-6
(7) = ii-7
(8) = ii-8
(9) = ii-9
(10) = ii-10
(11) = ii-11
(12) = ii-12
(13) = ii-13
(14) = ii-14
(15) = ii-15
MIB Information: hdr2CfgOutCatTest
1.3.6.1.4.1.429.4.48.1.1.1.45
mandatory read-write
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = ii-1
(2) = ii-2
(3) = ii-3
(4) = ii-4
(5) = ii-5
(6) = ii-6
(7) = ii-7
(8) = ii-8
(9) = ii-9
(10) = ii-10
(11) = ii-11
(12) = ii-12
(13) = ii-13
(14) = ii-14
(15) = ii-15
MIB Information: hdr2CfgOutCatMaintenance
1.3.6.1.4.1.429.4.48.1.1.1.46
mandatory read-write
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = ii-1
(2) = ii-2
(3) = ii-3
(4) = ii-4
(5) = ii-5
(6) = ii-6
(7) = ii-7
(8) = ii-8
(9) = ii-9
(10) = ii-10
(11) = ii-11
(12) = ii-12
(13) = ii-13
(14) = ii-14
(15) = ii-15
MIB Information: hdr2CfgDoubleAnswerDelay
1.3.6.1.4.1.429.4.48.1.1.1.47
mandatory read-write
Description: This object provides a delay timer used to tear down collect calls. The time between the first Answer and the Clearback is set to the programmed delay the time between the Clearback and second Answer is set to twice the programmed delay. If the delay is set to 0 the feature is disabled.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 255
Copyright © 2000 3Com Corporation.