|
|
|
|
MIB Information: mdmLi
1.3.6.1.4.1.429.1.6.2
MIB Information: mdmLiTable
1.3.6.1.4.1.429.1.6.2.1
not-accessible
Description: A list of configurable Line Interface objects for a modem. The number of table entries is given by modemNumber.
MIB Information: mdmLiEntry
1.3.6.1.4.1.429.1.6.2.1.1
not-accessible
Description: Objects which define the line interface characteristics for a particualar modem.
MIB Information: mdmLiIndex
1.3.6.1.4.1.429.1.6.2.1.1.1
mandatory read-only
Description: Index into the Line Interface table. This index is the value from the chassis mib entity relation table that is applicable for a particular modem.
Settings: INTEGER
MIB Information: mdmLiDialPause
1.3.6.1.4.1.429.1.6.2.1.1.2
mandatory read-write
Description: Duration in seconds for the pause(') option in the dial command and the pause between command re-executions(> and A>) Default = 2. Equates to the modem's S8 register.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 255
MIB Information: mdmLiCarrierRecDelay
1.3.6.1.4.1.429.1.6.2.1.1.3
mandatory read-write
Description: Duration in 10ths of a second that the remote modem's carrier signal must be present before recognition. Ignored at speeds above 2400. Equates to the modem's S9 register. Default=6.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 255
0 = 255
MIB Information: mdmLiToneDialTiming
1.3.6.1.4.1.429.1.6.2.1.1.5
mandatory read-write
Description: Duration and spacing in milliseconds of dialed Touch Tones. Equates to the modem's S10 register. Default=70.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 255
MIB Information: mdmLiDteRxDataDelay
1.3.6.1.4.1.429.1.6.2.1.1.6
mandatory read-write
Description: Duration in 10ths of a second that the modem inserts a RX transmission delay between CD and the first recieved character. Intended for custom applications and not recomended for general usage. Equates to the modem's S35 register. Default=0.
Settings: INTEGER
Syntax Ref. Type: RANGE
MIB Information: mdmLiCarrierLoss
1.3.6.1.4.1.429.1.6.2.1.1.4
mandatory read-write
Description: Duration in 10ths of a second the modem waits after loss of carrier before hanging up. This allows the modem to distinguish between a momentary lapse in line quality and a true disconnect. When equal to 255 the modem will remain off hook until DTR drops or an ATH command is recieved. Equates to the modem's S10 register. Default=7.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 255
MIB Information: mdmLiTransmiter
1.3.6.1.4.1.429.1.6.2.1.1.7
mandatory read-write
Description: Enables the modem to transmit data. Corresponds to the modem 'C' register. Default=2.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: mdmLiDialMode
1.3.6.1.4.1.429.1.6.2.1.1.8
mandatory read-write
Description: Determines whether the modem uses pulse or tone for dialing when initiating outgoing calls. Equates to the P and T registers in the modem. Default=tone(2).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = pulse
(2) = tone
MIB Information: mdmLiGuardTone
1.3.6.1.4.1.429.1.6.2.1.1.9
mandatory read-write
Description: This object is required for modems answering calls that originate from sites outside of North America. The modem's must be operating in either 1200 or 2400 bps and be using the V.32 answer sequence. This object defines what guard tone is used for answering calls. This object equates to the &G register in US Robotics modems. Default=none.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = none
(2) = european550
(3) = uk1800
MIB Information: mdmLiLeasedLine
1.3.6.1.4.1.429.1.6.2.1.1.10
mandatory read-write
Description: Enables modem to operate in leased line mode. When enabled the local an remote modems make a continuous connection without dialing. Should the connection be broken the modem's will attempt to automaticly reestablish it(see mdmCcLeasedLineRest). Equates to the modem's &L register Default = disabled.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
(3) = cellularHSTMode
MIB Information: mdmLiLeasedLineRestDelay
1.3.6.1.4.1.429.1.6.2.1.1.11
mandatory read-write
Description: Sets the duration in seconds of the delay between when the modem senses loss of carrier and when it attempts to reestablish a leased line connection. The default setting of 15 should be appropriate for most installations.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 255
MIB Information: mdmLiPulseMakeBreak
1.3.6.1.4.1.429.1.6.2.1.1.12
mandatory read-write
Description: Determines the ratio of off hook to on hook interval for Pulse dialing. Equates to the modem's &P register. Default=North America.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = northAmerica
(2) = britishCommonwealth
MIB Information: mdmLiAnswerTone
1.3.6.1.4.1.429.1.6.2.1.1.13
mandatory read-write
Description: Disables the 2100 Hz Answer tone allowing V.42 modems to connect more quickly and/or eliminating problems with older 2400-bps modems that do not recognise this tone. Equates to the modem's S27.3 register. Default=Enabled.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = enable
(2) = disable
MIB Information: mdmLiRemoteEscGuardTime
1.3.6.1.4.1.429.1.6.2.1.1.14
mandatory read-write
Description: Sets the duration in 20 millisecond increments of the guard time that the modem requires preceding and following the remote escape sequence.The default is 200 or 4 seconds.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 255
MIB Information: mdmLiRemoteEscChar
1.3.6.1.4.1.429.1.6.2.1.1.15
mandatory read-write
Description: Specifies the decimal value of the character used in the remote access escape code for entering online command mode on this modem from the remote site. Default = 126(~).
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 255
MIB Information: mdmLiRemAccessLimit
1.3.6.1.4.1.429.1.6.2.1.1.16
mandatory read-write
Description: Determines the number of attempts to enter remote online command mode that are allowed for any one connection. The default is 0 which disables the remote access functon.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 255
MIB Information: mdmLiRemPassword0
1.3.6.1.4.1.429.1.6.2.1.1.17
mandatory read-write
Description: The password that allows a dial-in user to gain view only access to this modems parameters. A maximum of 8 characters is allowed.
Settings: DisplayString
Syntax Ref. Type: SIZE
0 = 8
MIB Information: mdmLiRemPassword1
1.3.6.1.4.1.429.1.6.2.1.1.18
mandatory read-write
Description: The password used by a dial-in user to gain read-write access to this modems configuration. Maximum length is 8 characters.
Settings: DisplayString
Syntax Ref. Type: SIZE
0 = 8
MIB Information: mdmLiTransmitLevel
1.3.6.1.4.1.429.1.6.2.1.1.19
mandatory read-write
Description: Specifies the signal level of the modem transmitter in negative db.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 20
MIB Information: mdmLiSrc
1.3.6.1.4.1.429.1.6.2.1.1.20
optional read-write
Description: Specifies either NIC or TDM as the source for the line interface.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = nic
(2) = t1Tdm
(3) = priTdm
Copyright © 2000 3Com Corporation.