|
|
|
|
MIB Information: ds3
1.3.6.1.2.1.10.30
MIB Information: dsx3ConfigTable
1.3.6.1.2.1.10.30.5
not-accessible
MIB Information: dsx3ConfigEntry
1.3.6.1.2.1.10.30.5.1
not-accessible
MIB Information: dsx3LineIndex
1.3.6.1.2.1.10.30.5.1.1
current read-only
Description: This object should be made equal to ifIndex. The
next paragraph describes its previous usage.
Making the object equal to ifIndex allows propoer
use of ifStackTable. Previously, this object was the identifier of a
DS3/E3 Interface on a managed device. If there is
an ifEntry that is directly associated with this
and only this DS3/E3 interface, it should have the
same value as ifIndex. Otherwise, number the
dsx3LineIndices with an unique identifier
following the rules of choosing a number that is
greater than ifNumber and numbering the inside
interfaces (e.g., equipment side) with even
numbers and outside interfaces (e.g, network side)
with odd numbers."
Settings: InterfaceIndex
MIB Information: dsx3IfIndex
1.3.6.1.2.1.10.30.5.1.2
deprecated read-only
Description: This value for this object is equal to the value
of ifIndex from the Interfaces table of MIB II
(RFC 1213)."
Settings: InterfaceIndex
MIB Information: dsx3TimeElapsed
1.3.6.1.2.1.10.30.5.1.3
current read-only
Description: The number of seconds that have elapsed since the
beginning of the near end current error-
measurement period. If, for some reason, such as
an adjustment in the system's time-of-day clock,
the current interval exceeds the maximum value,
the agent will return the maximum value."
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 899
MIB Information: dsx3ValidIntervals
1.3.6.1.2.1.10.30.5.1.4
current read-only
Description: The number of previous near end intervals for
which data was collected. The value will be
96 unless the interface was brought online within
the last 24 hours, in which case the value will be
the number of complete 15 minute near end
intervals since the interface has been online. In
the case where the agent is a proxy, it is
possible that some intervals are unavailable. In
this case, this interval is the maximum interval
number for which data is available."
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 96
MIB Information: dsx3LineType
1.3.6.1.2.1.10.30.5.1.5
current read-write
Description: This variable indicates the variety of DS3 C-bit
or E3 application implementing this interface. The
type of interface affects the interpretation of
the usage and error statistics. The rate of DS3
is 44.736 Mbps and E3 is 34.368 Mbps. The
dsx3ClearChannel value means that the C-bits are
not used except for sending/receiving AIS.
The values, in sequence, describe:
TITLE: SPECIFICATION:
dsx3M23 ANSI T1.107-1988 [9]
dsx3SYNTRAN ANSI T1.107-1988 [9]
dsx3CbitParity ANSI T1.107a-1990 [9a]
dsx3ClearChannel ANSI T1.102-1987 [8]
e3Framed CCITT G.751 [12]
e3Plcp ETSI T/NA(91)18 [13]."
Settings: INTEGER
Syntax Ref. Type: ENUM
-1 = dsx3other
-2 = dsx3M23
-3 = dsx3SYNTRAN
-4 = dsx3CbitParity
-5 = dsx3ClearChannel
-6 = e3other
-7 = e3Framed
-8 = e3Plcp
MIB Information: dsx3LineCoding
1.3.6.1.2.1.10.30.5.1.6
current read-write
Settings: INTEGER
Description: This variable describes the variety of Zero Code
Suppression used on this interface, which in turn
affects a number of its characteristics.
dsx3B3ZS and e3HDB3 refer to the use of specified
patterns of normal bits and bipolar violations
which are used to replace sequences of zero bits
of a specified length.
Syntax Ref. Type: ENUM
-1 = dsx3Other
-2 = dsx3B3ZS
-3 = e3HDB3
MIB Information: dsx3SendCode
1.3.6.1.2.1.10.30.5.1.7
current read-write
Description: This variable indicates what type of code is
being sent across the DS3/E3 interface by the
device. (These are optional for E3 interfaces.)
Setting this variable causes the interface to
begin sending the code requested.
The values mean:
dsx3SendNoCode
sending looped or normal data
dsx3SendLineCode
sending a request for a line loopback
dsx3SendPayloadCode
sending a request for a payload loopback
(i.e., all DS1/E1s in a DS3/E3 frame)
dsx3SendResetCode
sending a loopback deactivation request
dsx3SendDS1LoopCode
requesting to loopback a particular DS1/E1
within a DS3/E3 frame. The DS1/E1 is
indicated in dsx3Ds1ForRemoteLoop.
dsx3SendTestPattern
sending a test pattern."
Settings: INTEGER
Syntax Ref. Type: ENUM
-1 = dsx3SendNoCode
-2 = dsx3SendLineCode
-3 = dsx3SendPayloadCode
-4 = dsx3SendResetCode
-5 = dsx3SendDS1LoopCode
-6 = dsx3SendTestPattern
MIB Information: dsx3CircuitIdentifier
1.3.6.1.2.1.10.30.5.1.8
current read-write
Description: This variable contains the transmission vendor's
circuit identifier, for the purpose of
facilitating troubleshooting."
Settings: DisplayString
Syntax Ref. Type: SIZE
0 = 255
MIB Information: dsx3LoopbackConfig
1.3.6.1.2.1.10.30.5.1.9
current read-write
Description: This variable represents the desired loopback
configuration of the DS3/E3 interface.
Settings: INTEGER
Syntax Ref. Type: ENUM
-1 = dsx3NoLoop
-2 = dsx3PayloadLoop
-3 = dsx3LineLoop
-4 = dsx3OtherLoop
-5 = dsx3InwardLoop
-6 = dsx3DualLoop
MIB Information: dsx3LineStatus
1.3.6.1.2.1.10.30.5.1.10
current read-only
Description: This variable indicates the Line Status of the
interface. It contains loopback state information
and failure state information. The dsx3LineStatus
is a bit map represented as a sum, therefore, it
can represent multiple failures and a loopback
(see dsx3LoopbackConfig object for the type of
loopback) simultaneously. The dsx3NoAlarm must be
set if and only if no other flag is set.
If the dsx3loopbackState bit is set, the loopback
in effect can be determined from the
dsx3loopbackConfig object.
The various bit positions are:
1 dsx3NoAlarm No alarm present
2 dsx3RcvRAIFailure Receiving Yellow/Remote
Alarm Indication
4 dsx3XmitRAIAlarm Transmitting Yellow/Remote
Alarm Indication
8 dsx3RcvAIS Receiving AIS failure state
16 dsx3XmitAIS Transmitting AIS
32 dsx3LOF Receiving LOF failure state
64 dsx3LOS Receiving LOS failure state
128 dsx3LoopbackState Looping the received signal
256 dsx3RcvTestCode Receiving a Test Pattern
512 dsx3OtherFailure any line status not defined
here
1024 dsx3UnavailSigState Near End in Unavailable Signal
State
2048 dsx3NetEquipOOS Carrier Equipment Out of Service"
Settings: INTEGER
Syntax Ref. Type: RANGE
1 = 4095
MIB Information: dsx3TransmitClockSource
1.3.6.1.2.1.10.30.5.1.11
current read-write
Description: The source of Transmit Clock.
loopTiming indicates that the recovered receive clock
is used as the transmit clock.
localTiming indicates that a local clock source is used
or that an external clock is attached to the box
containing the interface.
throughTiming indicates that transmit clock is derived
from the recovered receive clock of another DS3
interface."
Settings: INTEGER
Syntax Ref. Type: ENUM
-1 = loopTiming
-2 = localTiming
-3 = throughTiming
MIB Information: dsx3InvalidIntervals
1.3.6.1.2.1.10.30.5.1.12
current read-only
Description: The number of intervals in the range from 0 to
dsx3ValidIntervals for which no data is
available. This object will typically be zero
except in cases where the data for some intervals
are not available (e.g., in proxy situations)."
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 96
MIB Information: dsx3LineLength
1.3.6.1.2.1.10.30.5.1.13
current read-write
Description: The length of the ds3 line in meters. This
object provides information for line build out
circuitry if it exists and can use this object to
adjust the line build out."
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 64000
MIB Information: dsx3LineStatusLastChange
1.3.6.1.2.1.10.30.5.1.14
current read-only
Description: The value of MIB II's sysUpTime object at the
time this DS3/E3 entered its current line status
state. If the current state was entered prior to
the last re-initialization of the proxy-agent,
then this object contains a zero value."
Settings: TimeStamp
MIB Information: dsx3LineStatusChangeTrapEnable
1.3.6.1.2.1.10.30.5.1.15
current read-write
Description: Indicates whether dsx3LineStatusChange traps
should be generated for this interface."
DEFVAL { disabled }
Settings: INTEGER
Syntax Ref. Type: ENUM
-1 = enabled
-2 = disabled
MIB Information: dsx3LoopbackStatus
1.3.6.1.2.1.10.30.5.1.16
current read-only
Description: This variable represents the current state of the
loopback on the DS3 interface. It contains
information about loopbacks established by a
manager and remotely from the far end.
The dsx3LoopbackStatus is a bit map represented as
a sum, therefore is can represent multiple
loopbacks simultaneously.
The various bit positions are:
1 dsx3NoLoopback
2 dsx3NearEndPayloadLoopback
4 dsx3NearEndLineLoopback
8 dsx3NearEndOtherLoopback
16 dsx3NearEndInwardLoopback
32 dsx3FarEndPayloadLoopback
64 dsx3FarEndLineLoopback"
Settings: INTEGER
Syntax Ref. Type: RANGE
1 = 127
MIB Information: dsx3Channelization
1.3.6.1.2.1.10.30.5.1.17
current read-write
Description: Indicates whether this ds3/e3 is channelized or
unchannelized. The value of enabledDs1 indicates
that this is a DS3 channelized into DS1s. The
value of enabledDs3 indicated that this is a DS3
channelized into DS2s. Setting this object will
cause the creation or deletion of DS2 or DS1
entries in the ifTable. "
Settings: INTEGER
Syntax Ref. Type: ENUM
-1 = disabled
-2 = enabledDs1
-3 = enabledDs2
MIB Information: dsx3Ds1ForRemoteLoop
1.3.6.1.2.1.10.30.5.1.18
current read-write
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 29
MIB Information: dsx3CurrentTable
1.3.6.1.2.1.10.30.6
Description: The DS3/E3 current table contains various
statistics being collected for the current 15
minute interval."
not-accessible
MIB Information: dsx3CurrentEntry
1.3.6.1.2.1.10.30.6.1
not-accessible
MIB Information: dsx3CurrentIndex
1.3.6.1.2.1.10.30.6.1.1
current read-only
Description: The index value which uniquely identifies the
DS3/E3 interface to which this entry is
applicable. The interface identified by a
particular value of this index is the same
interface as identified by the same value an
dsx3LineIndex object instance."
Settings: InterfaceIndex
MIB Information: dsx3CurrentPESs
1.3.6.1.2.1.10.30.6.1.2
current read-only
Description: The counter associated with the number of P-bit
Errored Seconds."
Settings: PerfCurrentCount
MIB Information: dsx3CurrentPSESs
1.3.6.1.2.1.10.30.6.1.3
current read-only
Description: The counter associated with the number of P-bit
Severely Errored Seconds."
Settings: PerfCurrentCount
MIB Information: dsx3CurrentSEFSs
1.3.6.1.2.1.10.30.6.1.4
current read-only
Description: The counter associated with the number of
Severely Errored Framing Seconds."
Settings: PerfCurrentCount
MIB Information: dsx3CurrentUASs
1.3.6.1.2.1.10.30.6.1.5
current read-only
Description: The counter associated with the number of
Unavailable Seconds."
Settings: PerfCurrentCount
MIB Information: dsx3CurrentLCVs
1.3.6.1.2.1.10.30.6.1.6
current read-only
Description: The counter associated with the number of Line
Coding Violations."
Settings: PerfCurrentCount
MIB Information: dsx3CurrentPCVs
1.3.6.1.2.1.10.30.6.1.7
current read-only
Description: The counter associated with the number of P-bit
Coding Violations."
Settings: PerfCurrentCount
MIB Information: dsx3CurrentLESs
1.3.6.1.2.1.10.30.6.1.8
current read-only
Description: The number of Line Errored Seconds."
Settings: PerfCurrentCount
MIB Information: dsx3CurrentCCVs
1.3.6.1.2.1.10.30.6.1.9
current read-only
Description: The number of C-bit Coding Violations."
Settings: PerfCurrentCount
MIB Information: dsx3CurrentCESs
1.3.6.1.2.1.10.30.6.1.10
current read-only
Description: The number of C-bit Errored Seconds."
Settings: PerfCurrentCount
MIB Information: dsx3CurrentCSESs
1.3.6.1.2.1.10.30.6.1.11
current read-only
Description: The number of C-bit Severely Errored Seconds."
Settings: PerfCurrentCount
MIB Information: dsx3IntervalTable
1.3.6.1.2.1.10.30.7
Description: The DS3/E3 Interval Table contains various
statistics collected by each DS3/E3 Interface over
the previous 24 hours of operation. The past 24
hours are broken into 96 completed 15 minute
intervals. Each row in this table represents one
such interval (identified by dsx3IntervalNumber)
and for one specific interface (identifed by
dsx3IntervalIndex)."
not-accessible
MIB Information: dsx3IntervalEntry
1.3.6.1.2.1.10.30.7.1
not-accessible
MIB Information: dsx3IntervalIndex
1.3.6.1.2.1.10.30.7.1.1
current read-only
Description:
"The index value which uniquely identifies the
DS3/E3 interface to which this entry is
applicable. The interface identified by a
particular value of this index is the same
interface as identified by the same value an
dsx3LineIndex object instance."
Settings: InterfaceIndex
MIB Information: dsx3IntervalNumber
1.3.6.1.2.1.10.30.7.1.2
current read-only
Description:
"A number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the 15 minutes interval completed 23 hours and 45
minutes prior to interval 1."
Settings: INTEGER
Syntax Ref. Type: RANGE
1 = 96
MIB Information: dsx3IntervalPESs
1.3.6.1.2.1.10.30.7.1.3
current read-only
Description:
"The counter associated with the number of P-bit
Errored Seconds."
Settings: PerfIntervalCount
MIB Information: dsx3IntervalPSESs
1.3.6.1.2.1.10.30.7.1.4
current read-only
Description:
"The counter associated with the number of P-bit
Severely Errored Seconds."
Settings: PerfIntervalCount
MIB Information: dsx3IntervalSEFSs
1.3.6.1.2.1.10.30.7.1.5
current read-only
Description:
"The counter associated with the number of
Severely Errored Framing Seconds."
Settings: PerfIntervalCount
MIB Information: dsx3IntervalUASs
1.3.6.1.2.1.10.30.7.1.6
current read-only
Description:
"The counter associated with the number of
Unavailable Seconds. This object may decrease if
the occurance of unavailable seconds occurs across
an inteval boundary."
Settings: PerfIntervalCount
MIB Information: dsx3IntervalLCVs
1.3.6.1.2.1.10.30.7.1.7
current read-only
Description:
"The counter associated with the number of Line
Coding Violations."
Settings: PerfIntervalCount
MIB Information: dsx3IntervalPCVs
1.3.6.1.2.1.10.30.7.1.8
current read-only
Description:
"The counter associated with the number of P-bit
Coding Violations."
Settings: PerfIntervalCount
MIB Information: dsx3IntervalLESs
1.3.6.1.2.1.10.30.7.1.9
current read-only
Description:
"The number of Line Errored Seconds (BPVs or
illegal zero sequences)."
Settings: PerfIntervalCount
MIB Information: dsx3IntervalCCVs
1.3.6.1.2.1.10.30.7.1.10
current read-only
Description:
"The number of C-bit Coding Violations."
Settings: PerfIntervalCount
MIB Information: dsx3IntervalCESs
1.3.6.1.2.1.10.30.7.1.11
current read-only
Description:
"The number of C-bit Errored Seconds."
Settings: PerfIntervalCount
MIB Information: dsx3IntervalCSESs
1.3.6.1.2.1.10.30.7.1.12
current read-only
Description:
"The number of C-bit Severely Errored Seconds."
Settings: PerfIntervalCount
MIB Information: dsx3IntervalValidData
1.3.6.1.2.1.10.30.7.1.13
current read-only
Description:
"This variable indicates if the data for this
interval is valid."
Settings: TruthValue
MIB Information: dsx3TotalTable
1.3.6.1.2.1.10.30.8
not-accessible
MIB Information: dsx3TotalEntry
1.3.6.1.2.1.10.30.8.1
not-accessible
MIB Information: dsx3TotalIndex
1.3.6.1.2.1.10.30.8.1.1
current read-only
Description:
"The index value which uniquely identifies the
DS3/E3 interface to which this entry is
applicable. The interface identified by a
particular value of this index is the same
interface as identified by the same value an
dsx3LineIndex object instance."
Settings: InterfaceIndex
MIB Information: dsx3TotalPESs
1.3.6.1.2.1.10.30.8.1.2
current read-only
Description:
"The counter associated with the number of P-bit
Errored Seconds, encountered by a DS3 interface in
the previous 24 hour interval. Invalid 15 minute
intervals count as 0."
Settings: PerfTotalCount
MIB Information: dsx3TotalPSESs
1.3.6.1.2.1.10.30.8.1.3
current read-only
Description:
"The counter associated with the number of P-bit
Severely Errored Seconds, encountered by a DS3
interface in the previous 24 hour interval.
Invalid 15 minute intervals count as 0."
Settings: PerfTotalCount
MIB Information: dsx3TotalSEFSs
1.3.6.1.2.1.10.30.8.1.4
current read-only
Description:
"The counter associated with the number of
Severely Errored Framing Seconds, encountered by a
DS3/E3 interface in the previous 24 hour interval.
Invalid 15 minute intervals count as 0."
Settings: PerfTotalCount
MIB Information: dsx3TotalUASs
1.3.6.1.2.1.10.30.8.1.5
current read-only
Description:
"The counter associated with the number of
Unavailable Seconds, encountered by a DS3
interface in the previous 24 hour interval.
Invalid 15 minute intervals count as 0."
Settings: PerfTotalCount
MIB Information: dsx3TotalLCVs
1.3.6.1.2.1.10.30.8.1.6
current read-only
Description:
"The counter associated with the number of Line
Coding Violations encountered by a DS3/E3
interface in the previous 24 hour interval.
Invalid 15 minute intervals count as 0."
Settings: PerfTotalCount
MIB Information: dsx3TotalPCVs
1.3.6.1.2.1.10.30.8.1.7
current read-only
Description:
"The counter associated with the number of P-bit
Coding Violations, encountered by a DS3 interface
in the previous 24 hour interval. Invalid 15
minute intervals count as 0."
Settings: PerfTotalCount
MIB Information: dsx3TotalLESs
1.3.6.1.2.1.10.30.8.1.8
current read-only
Description:
"The number of Line Errored Seconds (BPVs or
illegal zero sequences) encountered by a DS3/E3
interface in the previous 24 hour interval.
Invalid 15 minute intervals count as 0."
Settings: PerfTotalCount
MIB Information: dsx3TotalCCVs
1.3.6.1.2.1.10.30.8.1.9
current read-only
Description:
"The number of C-bit Coding Violations encountered
by a DS3 interface in the previous 24 hour
interval. Invalid 15 minute intervals count as 0."
Settings: PerfTotalCount
MIB Information: dsx3TotalCESs
1.3.6.1.2.1.10.30.8.1.10
current read-only
Description:
"The number of C-bit Errored Seconds encountered
by a DS3 interface in the previous 24 hour
interval. Invalid 15 minute intervals count as 0."
Settings: PerfTotalCount
MIB Information: dsx3TotalCSESs
1.3.6.1.2.1.10.30.8.1.11
current read-only
Description:
"The number of C-bit Severely Errored Seconds
encountered by a DS3 interface in the previous 24
hour interval. Invalid 15 minute intervals count
as 0."
Settings: PerfTotalCount
MIB Information: dsx3FarEndConfigTable
1.3.6.1.2.1.10.30.9
not-accessible
Description:
"The DS3 Far End Configuration Table contains
configuration information reported in the C-bits
from the remote end."
MIB Information: dsx3FarEndConfigEntry
1.3.6.1.2.1.10.30.9.1
not-accessible
Description:
"An entry in the DS3 Far End Configuration table."
MIB Information: dsx3FarEndLineIndex
1.3.6.1.2.1.10.30.9.1.1
current read-only
Description:
"The index value which uniquely identifies the DS3
interface to which this entry is applicable. The
interface identified by a particular value of this
index is the same interface as identified by the
same value an dsx3LineIndex object instance."
Settings: InterfaceIndex
MIB Information: dsx3FarEndEquipCode
1.3.6.1.2.1.10.30.9.1.2
current read-write
Description:
"This is the Far End Equipment Identification code
that describes the specific piece of equipment.
It is sent within the Path Identification
Message."
Settings: DisplayString
Syntax Ref. Type: SIZE
0 = 10
MIB Information: dsx3FarEndLocationIDCode
1.3.6.1.2.1.10.30.9.1.3
current read-write
Description:
"This is the Far End Location Identification code
that describes the specific location of the
equipment. It is sent within the Path
Identification Message."
Settings: DisplayString
Syntax Ref. Type: SIZE
0 = 11
MIB Information: dsx3FarEndFrameIDCode
1.3.6.1.2.1.10.30.9.1.4
current read-write
Description:
"This is the Far End Frame Identification code
that identifies where the equipment is located
within a building at a given location. It is sent
within the Path Identification Message."
Settings: DisplayString
Syntax Ref. Type: SIZE
0 = 10
MIB Information: dsx3FarEndUnitCode
1.3.6.1.2.1.10.30.9.1.5
current read-write
Description:
"This is the Far End code that identifies the
equipment location within a bay. It is sent
within the Path Identification Message."
Settings: DisplayString
Syntax Ref. Type: SIZE
0 = 6
MIB Information: dsx3FarEndFacilityIDCode
1.3.6.1.2.1.10.30.9.1.6
current read-write
Description:
"This code identifies a specific Far End DS3 path.
It is sent within the Path Identification
Message."
Settings: DisplayString
Syntax Ref. Type: SIZE
0 = 38
MIB Information: dsx3FarEndCurrentTable
1.3.6.1.2.1.10.30.10
not-accessible
Description:
"The DS3 Far End Current table contains various
statistics being collected for the current 15
minute interval. The statistics are collected
from the far end block error code within the C-
bits."
MIB Information: dsx3FarEndCurrentEntry
1.3.6.1.2.1.10.30.10.1
not-accessible
Description:
"An entry in the DS3 Far End Current table.
MIB Information: dsx3FarEndCurrentIndex
1.3.6.1.2.1.10.30.10.1.1
current read-only
Description:
"The index value which uniquely identifies the DS3
interface to which this entry is applicable. The
interface identified by a particular value of this
index is identical to the interface identified by
the same value of dsx3LineIndex."
Settings: InterfaceIndex
MIB Information: dsx3FarEndTimeElapsed
1.3.6.1.2.1.10.30.10.1.2
current read-only
Description:
"The number of seconds that have elapsed since the
beginning of the far end current error-measurement
period. If, for some reason, such as an
adjustment in the system's time-of-day clock, the
current interval exceeds the maximum value, the
agent will return the maximum value."
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 899
MIB Information: dsx3FarEndValidIntervals
1.3.6.1.2.1.10.30.10.1.3
current read-only
Description:
"The number of previous far end intervals for
which data was collected. The value will be
96 unless the interface was brought online within
the last 24 hours, in which case the value will be
the number of complete 15 minute far end intervals
since the interface has been online."
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 96
MIB Information: dsx3FarEndCurrentCESs
1.3.6.1.2.1.10.30.10.1.4
current read-only
Description:
"The counter associated with the number of Far Far
End C-bit Errored Seconds."
Settings: PerfCurrentCount
MIB Information: dsx3FarEndCurrentCSESs
1.3.6.1.2.1.10.30.10.1.5
current read-only
Description:
"The counter associated with the number of Far End
C-bit Severely Errored Seconds."
Settings: PerfCurrentCount
MIB Information: dsx3FarEndCurrentCCVs
1.3.6.1.2.1.10.30.10.1.6
current read-only
Description:
"The counter associated with the number of Far End
C-bit Coding Violations reported via the far end
block error count."
Settings: PerfCurrentCount
MIB Information: dsx3FarEndCurrentUASs
1.3.6.1.2.1.10.30.10.1.7
current read-only
Description:
"The counter associated with the number of Far End
C-bit Coding Violations reported via the far end
block error count."
Settings: PerfCurrentCount
MIB Information: dsx3FarEndInvalidIntervals
1.3.6.1.2.1.10.30.10.1.8
current read-only
Description:
"The number of intervals in the range from 0 to
dsx3FarEndValidIntervals for which no data is
available. This object will typically be zero
except in cases where the data for some intervals
are not available (e.g., in proxy situations)."
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 96
MIB Information: dsx3FarEndIntervalTable
1.3.6.1.2.1.10.30.11
not-accessible
Description:
"The DS3 Far End Interval Table contains various
statistics collected by each DS3 interface over
the previous 24 hours of operation. The past 24
hours are broken into 96 completed 15 minute
intervals."
MIB Information: dsx3FarEndIntervalEntry
1.3.6.1.2.1.10.30.11.1
not-accessible
Description:
"An entry in the DS3 Far End Interval table.
MIB Information: dsx3FarEndIntervalIndex
1.3.6.1.2.1.10.30.11.1.1
current read-only
Description:
"The index value which uniquely identifies the DS3
interface to which this entry is applicable. The
interface identified by a particular value of this
index is identical to the interface identified by
the same value of dsx3LineIndex."
Settings: InterfaceIndex
MIB Information: dsx3FarEndIntervalNumber
1.3.6.1.2.1.10.30.11.1.2
current read-only
Description:
"A number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the 15 minutes interval completed 23 hours and 45
minutes prior to interval 1."
Settings: INTEGER
Syntax Ref. Type: RANGE
1 = 96
MIB Information: dsx3FarEndIntervalCESs
1.3.6.1.2.1.10.30.11.1.3
current read-only
Description:
"The counter associated with the number of Far End
C-bit Errored Seconds encountered by a DS3
interface in one of the previous 96, individual 15
minute, intervals. In the case where the agent is
a proxy and data is not available, return
noSuchInstance."
Settings: PerfIntervalCount
MIB Information: dsx3FarEndIntervalCSESs
1.3.6.1.2.1.10.30.11.1.4
current read-only
Description:
"The counter associated with the number of Far End
C-bit Severely Errored Seconds."
Settings: PerfIntervalCount
MIB Information: dsx3FarEndIntervalCCVs
1.3.6.1.2.1.10.30.11.1.5
current read-only
Description:
"The counter associated with the number of Far End
C-bit Coding Violations reported via the far end
block error count."
Settings: PerfIntervalCount
MIB Information: dsx3FarEndIntervalUASs
1.3.6.1.2.1.10.30.11.1.6
current read-only
Description:
"The counter associated with the number of Far End
unavailable seconds."
Settings: PerfIntervalCount
MIB Information: dsx3FarEndIntervalValidData
1.3.6.1.2.1.10.30.11.1.7
current read-only
Description:
"This variable indicates if the data for this
interval is valid."
Settings: TruthValue
MIB Information: dsx3FarEndTotalTable
1.3.6.1.2.1.10.30.12
not-accessible
Description:
"The DS3 Far End Total Table contains the
cumulative sum of the various statistics for the
24 hour period preceding the current interval.
MIB Information: dsx3FarEndTotalEntry
1.3.6.1.2.1.10.30.12.1
not-accessible
Description:
"An entry in the DS3 Far End Total table."
MIB Information: dsx3FarEndTotalIndex
1.3.6.1.2.1.10.30.12.1.1
current read-only
Description:
"The index value which uniquely identifies the DS3
interface to which this entry is applicable. The
interface identified by a particular value of this
index is identical to the interface identified by
the same value of dsx3LineIndex."
Settings: InterfaceIndex
MIB Information: dsx3FarEndTotalCESs
1.3.6.1.2.1.10.30.12.1.2
current read-only
Description:
"The counter associated with the number of Far End
C-bit Errored Seconds encountered by a DS3
interface in the previous 24 hour interval.
Invalid 15 minute intervals count as 0."
Settings: PerfTotalCount
MIB Information: dsx3FarEndTotalCSESs
1.3.6.1.2.1.10.30.12.1.3
current read-only
Description:
"The counter associated with the number of Far End
C-bit Severely Errored Seconds encountered by a
DS3 interface in the previous 24 hour interval.
Invalid 15 minute intervals count as 0."
Settings: PerfTotalCount
MIB Information: dsx3FarEndTotalCCVs
1.3.6.1.2.1.10.30.12.1.4
current read-only
Description:
"The counter associated with the number of Far End
C-bit Coding Violations reported via the far end
block error count encountered by a DS3 interface
in the previous 24 hour interval. Invalid 15
minute intervals count as 0."
Settings: PerfTotalCount
MIB Information: dsx3FarEndTotalUASs
1.3.6.1.2.1.10.30.12.1.5
current read-only
Description:
"The counter associated with the number of Far End
unavailable seconds encountered by a DS3 interface
in the previous 24 hour interval. Invalid 15
minute intervals count as 0."
Settings: PerfTotalCount
MIB Information: dsx3FracTable
1.3.6.1.2.1.10.30.13
Description:
"This table is deprecated in favour of using
ifStackTable.
Implementation of this table was optional. It was
designed for those systems dividing a DS3/E3 into
channels containing different data streams that
are of local interest.
The DS3/E3 fractional table identifies which
DS3/E3 channels associated with a CSU are being
used to support a logical interface, i.e., an
entry in the interfaces table from the Internet-
standard MIB.
For example, consider a DS3 device with 4 high
speed links carrying router traffic, a feed for
voice, a feed for video, and a synchronous channel
for a non-routed protocol. We might describe the
allocation of channels, in the dsx3FracTable, as
follows:
dsx3FracIfIndex.2. 1 = 3 dsx3FracIfIndex.2.15 = 4
dsx3FracIfIndex.2. 2 = 3 dsx3FracIfIndex.2.16 = 6
dsx3FracIfIndex.2. 3 = 3 dsx3FracIfIndex.2.17 = 6
dsx3FracIfIndex.2. 4 = 3 dsx3FracIfIndex.2.18 = 6
dsx3FracIfIndex.2. 5 = 3 dsx3FracIfIndex.2.19 = 6
dsx3FracIfIndex.2. 6 = 3 dsx3FracIfIndex.2.20 = 6
dsx3FracIfIndex.2. 7 = 4 dsx3FracIfIndex.2.21 = 6
dsx3FracIfIndex.2. 8 = 4 dsx3FracIfIndex.2.22 = 6
dsx3FracIfIndex.2. 9 = 4 dsx3FracIfIndex.2.23 = 6
dsx3FracIfIndex.2.10 = 4 dsx3FracIfIndex.2.24 = 6
dsx3FracIfIndex.2.11 = 4 dsx3FracIfIndex.2.25 = 6
dsx3FracIfIndex.2.12 = 5 dsx3FracIfIndex.2.26 = 6
dsx3FracIfIndex.2.13 = 5 dsx3FracIfIndex.2.27 = 6
dsx3FracIfIndex.2.14 = 5 dsx3FracIfIndex.2.28 = 6
For dsx3M23, dsx3 SYNTRAN, dsx3CbitParity, and
dsx3ClearChannel there are 28 legal channels,
numbered 1 throug h 28.
For e3Framed there are 16 legal channels, numbered
1 through 16. The channels (1..16) correspond
directly to the equivalently numbered time-slots."
not-accessible
MIB Information: dsx3FracEntry
1.3.6.1.2.1.10.30.13.1
not-accessible
Description:
"An entry in the DS3 Fractional table."
MIB Information: dsx3FracIndex
1.3.6.1.2.1.10.30.13.1.1
deprecated read-only
Description:
"The index value which uniquely identifies the
DS3 interface to which this entry is applicable
The interface identified by a particular value
of this index is the same interface as
identified by the same value an dsx3LineIndex
object instance."
Settings: INTEGER
Syntax Ref. Type: RANGE
1 = 2147483647
MIB Information: dsx3FracNumber
1.3.6.1.2.1.10.30.13.1.2
deprecated read-only
Description:
"The channel number for this entry."
Settings: INTEGER
Syntax Ref. Type: RANGE
1 = 31
MIB Information: dsx3FracIfIndex
1.3.6.1.2.1.10.30.13.1.3
deprecated read-write
Description:
"An index value that uniquely identifies an
interface. The interface identified by a
particular value of this index is the same
interface as identified by the same value an
ifIndex object instance. If no interface is
currently using a channel, the value should be
zero. If a single interface occupies more than
one time slot, that ifIndex value will be found
in multiple time slots."
Settings: INTEGER
Syntax Ref. Type: RANGE
1 = 2147483647
Copyright © 2000 3Com Corporation.