|
|
|
|
MIB Information: ux25
1.3.6.1.4.1.429.1.10
MIB Information: ux25AdmnChannelTable
1.3.6.1.4.1.429.1.10.1
not-accessible
Description: Defines objects for the parameters of an X.25 interface which the administrator can read and set.
MIB Information: ux25AdmnChannelEntry
1.3.6.1.4.1.429.1.10.1.1
not-accessible
Description: Entries of ux25AdmnChannelTable.
MIB Information: ux25AdmnChanneIndex
1.3.6.1.4.1.429.1.10.1.1.1
mandatory read-only
Description: A unique value for each X.25 subnetwork entity in the chassis. The value of this object matches the value of the index of the corresponding X.25 subnetwork entity entry in the entity table of the chassis MIB.
Settings: INTEGER
MIB Information: ux25AdmnNetMode
1.3.6.1.4.1.429.1.10.1.1.2
mandatory read-write
Description: Selects the network protocol to be used.Default=x2584(3).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = x25Llc
(2) = x2588
(3) = x2584
(4) = x2580
(5) = pss
(6) = austpac
(7) = datapac
(8) = ddn
(9) = telenet
(10) = transpac
(11) = tymnet
(12) = datexP
(13) = ddxP
(14) = venusP
(15) = accunet
(16) = itapac
(17) = datapak
(18) = datanet
(19) = dcs
(20) = telepac
(21) = fDatapac
(22) = finpac
(23) = pacnet
(24) = luxpac
MIB Information: ux25AdmnProtocolVersion
1.3.6.1.4.1.429.1.10.1.1.3
mandatory read-write
Description: Determines the X.25 protocol version being used on the network. A network mode of X25_LLC overides this field to the 1984 standard.Default=x25ver84(3).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = x25ver80
(2) = x25ver84
(3) = x25ver88
MIB Information: ux25AdmnInterfaceMode
1.3.6.1.4.1.429.1.10.1.1.4
mandatory read-write
Description: Indicates the DTE/DCE nature of the link. The DXE parameter is resolved using ISO 8208 for DTE-DTE operation. Default=dteMode(2).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = dceMode
(2) = dteMode
(3) = dxeMode
MIB Information: ux25AdmnLowestPVCVal
1.3.6.1.4.1.429.1.10.1.1.5
mandatory read-write
Description: Low end of the Permanent Virtual Circuit range. If both the Low and High ends of the range are set to 0 there are no PVCs.Default=0.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 4095
MIB Information: ux25AdmnHighestPVCVal
1.3.6.1.4.1.429.1.10.1.1.6
mandatory read-write
Description: High end of the Permanent Virtual Circuit range. If both the Low and High ends of the range are set to 0 there are no PVCs.Default=0.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 4095
MIB Information: ux25AdmnChannelLIC
1.3.6.1.4.1.429.1.10.1.1.7
mandatory read-write
Description: Low end of the one-way incoming logical channel. If both Low and High ends of the channel are set to 0 there are no one-way incoming channels.Default=0.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 4095
MIB Information: ux25AdmnChannelHIC
1.3.6.1.4.1.429.1.10.1.1.8
mandatory read-write
Description: High end of the one-way incoming logical channel. If both Low and High ends of the channel are set to 0 there are no one-way incoming channels.Default=0.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 4095
MIB Information: ux25AdmnChannelLTC
1.3.6.1.4.1.429.1.10.1.1.9
mandatory read-write
Description: Low end of the two-way incoming logical channel. If both Low and High ends of the channel are set to 0 there are no two-way incoming channels.Default=1024.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 4095
MIB Information: ux25AdmnChannelHTC
1.3.6.1.4.1.429.1.10.1.1.10
mandatory read-write
Description: High end of the two-way incoming logical channel. If both Low and High ends of the channel are set to 0 there are no two-way incoming channels.Default=1087.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 4095
MIB Information: ux25AdmnChannelLOC
1.3.6.1.4.1.429.1.10.1.1.11
mandatory read-write
Description: Low end of the one-way outgoing logical channel. If both Low and High ends of the channel are set to 0 there are no one-way outgoing channels.Default=0.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 4095
MIB Information: ux25AdmnChannelHOC
1.3.6.1.4.1.429.1.10.1.1.12
mandatory read-write
Description: High end of the one-way outgoing logical channel. If both Low and High ends of the channel are set to 0 there are no one-way outgoing channels.Default=0.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 4095
MIB Information: ux25AdmnClassTable
1.3.6.1.4.1.429.1.10.2
not-accessible
Description: Defines objects for the parameters of an X.25 interface which the administrator can read and set.
MIB Information: ux25AdmnClassEntry
1.3.6.1.4.1.429.1.10.2.1
not-accessible
Description: Entries of ux25AdmnClassTable.
MIB Information: ux25AdmnClassIndex
1.3.6.1.4.1.429.1.10.2.1.1
mandatory read-only
Description: A unique value for each X.25 subnetwork entity in the chassis. The value of this object matches the value of the index of the corresponding X.25 subnetwork entity entry in the entity table of the chassis MIB.
Settings: INTEGER
(1) = tcReserved0
(2) = tcReserved1
(3) = tcReserved2
(4) = tc75
(5) = tc150
(6) = tc300
(7) = tc600
(8) = tc1200
(9) = tc2400
MIB Information: ux25AdmnLocMaxThruPutClass
1.3.6.1.4.1.429.1.10.2.1.2
mandatory read-write
Description: The maximum value of the throughput class Quality of Service parameter which is supported. According to ISO 8208 this parameter is bounded in the range >=3 and <=12 corresponding to a range 75 to 48000 bits/second. The range supported here is 0 to 15 for non-standard X.25 implementations which use the Throughput Class Window/Packet Parameters (Group II).Default=12.
Settings: INTEGER
Syntax Ref. Type: ENUM
(10) = tc4800
(11) = tc9600
(12) = tc19200
(13) = tc48000
(14) = tcReserved13
(15) = tcReserved14
(16) = tcReserved15
MIB Information: ux25AdmnRemMaxThruPutClass
1.3.6.1.4.1.429.1.10.2.1.3
mandatory read-write
Description: The maximum value of the throughput class Quality of Service parameter which is supported. According to ISO 8208 this parameter is bounded in the range >=3 and <=12 corresponding to a range 75 to 48000 bits/second. The range supported here is 0 to 15 for non-standard X.25 implementations which use the Throughput Class Window/Packet Parameters (Group II).Default=12.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = tcReserved0
(2) = tcReserved1
(3) = tcReserved2
(4) = tc75
(5) = tc150
(6) = tc300
(7) = tc600
(8) = tc1200
(9) = tc2400
(10) = tc4800
(11) = tc9600
(12) = tc19200
(13) = tc48000
(14) = tcReserved13
(15) = tcReserved14
(16) = tcReserved15
MIB Information: ux25AdmnLocDefThruPutClass
1.3.6.1.4.1.429.1.10.2.1.4
mandatory read-write
Description: The default throughput class that is defined for the local-to-remote direction. In some networks such as TELENET negotiation of throughput class is constrained to be towards a configured default throughput class. In other PSDNs this value should be set equal to the value of the Maximum Local Throughput Class.Default=12.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = tcReserved0
(2) = tcReserved1
(3) = tcReserved2
(4) = tc75
(5) = tc150
(6) = tc300
(7) = tc600
(8) = tc1200
(9) = tc2400
(10) = tc4800
(11) = tc9600
(12) = tc19200
(13) = tc48000
(14) = tcReserved13
(15) = tcReserved14
(16) = tcReserved15
MIB Information: ux25AdmnRemDefThruPutClass
1.3.6.1.4.1.429.1.10.2.1.5
mandatory read-write
Description: The default throughput class value defined for remote-to-local direction. In some networks such as TELENET negotiation of throughput class is constrained to be towards a configured default throughput class. In other PSDNs this value should be set equal to the value of the Maximum Remote Throughput Class.Default=12.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = tcReserved0
(2) = tcReserved1
(3) = tcReserved2
(4) = tc75
(5) = tc150
(6) = tc300
(7) = tc600
(8) = tc1200
(9) = tc2400
(10) = tc4800
(11) = tc9600
(12) = tc19200
(13) = tc48000
(14) = tcReserved13
(15) = tcReserved14
(16) = tcReserved15
MIB Information: ux25AdmnLocMinThruPutClass
1.3.6.1.4.1.429.1.10.2.1.6
mandatory read-write
Description: According to ISO 8208 the throughput class parameter is defined in the range of >=3 to <=12. Some PSDNs may provide different mapping in which case this parameter is the minimum value.Default=3.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = tcReserved0
(2) = tcReserved1
(3) = tcReserved2
(4) = tc75
(5) = tc150
(6) = tc300
(7) = tc600
(8) = tc1200
(9) = tc2400
(10) = tc4800
(11) = tc9600
(12) = tc19200
(13) = tc48000
(14) = tcReserved13
(15) = tcReserved14
(16) = tcReserved15
MIB Information: ux25AdmnRemMinThruPutClass
1.3.6.1.4.1.429.1.10.2.1.7
mandatory read-write
Description: According to ISO 8208 the throughput class parameter is defined in the range of >=3 to <=12. Some PSDNs may provide different mapping in which case this parameter is the minimum value.Default=3.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = tcReserved0
(2) = tcReserved1
(3) = tcReserved2
(4) = tc75
(5) = tc150
(6) = tc300
(7) = tc600
(8) = tc1200
(9) = tc2400
(10) = tc4800
(11) = tc9600
(12) = tc19200
(13) = tc48000
(14) = tcReserved13
(15) = tcReserved14
(16) = tcReserved15
MIB Information: ux25AdmnThclassNegToDef
1.3.6.1.4.1.429.1.10.2.1.8
mandatory read-write
Description: Determines if throughput class negotiation will be used for certain network procedures.Default=disable(1).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25AdmnThclassType
1.3.6.1.4.1.429.1.10.2.1.9
mandatory read-write
Description: Defines which throughput class encodings can be used to assign packet and window sizes. Some implementations of X.25 do not use the X.25 packet and window negotiation and rely on mapping the throughput class to these parameters.Default=noTcType(1).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = noTcType
(2) = loNibble
(3) = highNibble
(4) = bothNibbles
MIB Information: ux25AdmnThclassWinMap
1.3.6.1.4.1.429.1.10.2.1.10
mandatory read-write
Description: The mapping between throughput class and a window parameter. Each number has a range of 1 to 127.Default=3.3.3.3.3.3.3.3.3.3.3.3.3.3.3.3
Settings: DisplayString
Syntax Ref. Type: SIZE
31 = 63
MIB Information: ux25AdmnThclassPackMap
1.3.6.1.4.1.429.1.10.2.1.11
mandatory read-write
Description: The mapping between the throughput class and a packet parameter. Each number has a range of 4 to 12.Default=7.7.7.7.7.7.7.7.7.7.7.7.7.7.7.7
Settings: DisplayString
Syntax Ref. Type: SIZE
31 = 47
MIB Information: ux25AdmnPacketTable
1.3.6.1.4.1.429.1.10.3
not-accessible
Description: Defines objects for the parameters of an X.25 interface which the administrator can read and set.
MIB Information: ux25AdmnPacketEntry
1.3.6.1.4.1.429.1.10.3.1
not-accessible
Description: Entries of ux25AdmnPacketTable.
MIB Information: ux25AdmnPacketIndex
1.3.6.1.4.1.429.1.10.3.1.1
mandatory read-only
Description: A unique value for each X.25 subnetwork entity in the chassis. The value of this object matches the value of the index of the corresponding X.25 subnetwork entity entry in the entity table of the chassis MIB.
Settings: INTEGER
MIB Information: ux25AdmnPktSequencing
1.3.6.1.4.1.429.1.10.3.1.2
mandatory read-write
Description: Indicates whether modulo 8 or 128 sequence numbering operates on the network.Default=pktSeq8(16).
Settings: INTEGER
Syntax Ref. Type: ENUM
(16) = pktSeq8
(32) = pktSeq128
MIB Information: ux25AdmnLocMaxPktSize
1.3.6.1.4.1.429.1.10.3.1.3
mandatory read-write
Description: Maximum acceptable size of packets in the local-to-remote direction. On an incoming call a value for the packet size parameter greater than this value will be negotiated down to an acceptable size when the call is accepted.Default=maxPktSz256(8).
Settings: INTEGER
Syntax Ref. Type: ENUM
(7) = maxPktSz128
(8) = maxPktSz256
(9) = maxPktSz512
MIB Information: ux25AdmnRemMaxPktSize
1.3.6.1.4.1.429.1.10.3.1.4
mandatory read-write
Description: Maximum acceptable size of packets in the remote-to-local direction. On an incoming call a value for the packet size parameter greater than this value will be negotiated down to an acceptable size when the call is accepted.Default=maxPktSz256(8).
Settings: INTEGER
Syntax Ref. Type: ENUM
(7) = maxPktSz128
(8) = maxPktSz256
(9) = maxPktSz512
MIB Information: ux25AdmnLocDefPktSize
1.3.6.1.4.1.429.1.10.3.1.5
mandatory read-write
Description: Specifies the value of the default packet size for the direction local-to-remote which may be nonstandard provided the value is agreed between the communicating parties on the LAN or between the DTE and DCE.Default=defPktSz256(8).
Settings: INTEGER
Syntax Ref. Type: ENUM
(4) = defPktSz16
(5) = defPktSz32
(6) = defPktSz64
(7) = defPktSz128
(8) = defPktSz256
(9) = defPktSz512
MIB Information: ux25AdmnRemDefPktSize
1.3.6.1.4.1.429.1.10.3.1.6
mandatory read-write
Description: Specifies the value of the default packet size for the direction remote-to-local which may be nonstandard provided the value is agreed between the communicating parties on the LAN or between the DTE and DCE.Default=defPktSz256(8).
Settings: INTEGER
Syntax Ref. Type: ENUM
(4) = defPktSz16
(5) = defPktSz32
(6) = defPktSz64
(7) = defPktSz128
(8) = defPktSz256
(9) = defPktSz512
MIB Information: ux25AdmnLocMaxWinSize
1.3.6.1.4.1.429.1.10.3.1.7
mandatory read-write
Description: Specifies the maximum local window size. NOTE: 127 allowed only for modulo 128 networks.Default=7.
Settings: INTEGER
Syntax Ref. Type: RANGE
2 = 127
MIB Information: ux25AdmnRemMaxWinSize
1.3.6.1.4.1.429.1.10.3.1.8
mandatory read-write
Description: Specifies the maximum remote window size. NOTE: 127 allowed only for modulo 128 networks.Default=7.
Settings: INTEGER
Syntax Ref. Type: RANGE
2 = 127
MIB Information: ux25AdmnLocDefWinSize
1.3.6.1.4.1.429.1.10.3.1.9
mandatory read-write
Description: Specifies the value of the default window size which may be nonstandard provided the value is agreed on by all parties on the LAN between the DTE and DCE. NOTE: The sequence numbering scheme affects the range of this parameter.Default=2.
Settings: INTEGER
Syntax Ref. Type: RANGE
1 = 127
MIB Information: ux25AdmnRemDefWinSize
1.3.6.1.4.1.429.1.10.3.1.10
mandatory read-write
Description: Specifies the value of the default window size which may be nonstandard provided the value is agreed on by all parties on the LAN between the DTE and DCE. NOTE: The sequence numbering scheme affects the range of this parameter.Default=2.
Settings: INTEGER
Syntax Ref. Type: RANGE
1 = 127
MIB Information: ux25AdmnMaxNSDULimit
1.3.6.1.4.1.429.1.10.3.1.11
mandatory read-write
Description: The default maximum length beyond which concatenation is stopped and data currently held is passed to the Network Service user.Default=256.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 32000
MIB Information: ux25AdmnAccNoDiagnostic
1.3.6.1.4.1.429.1.10.3.1.12
mandatory read-write
Description: Allow the omission of the diagnostic byte in incoming RESTART CLEAR and RESET INDICATION packets.Default=disable(1).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25AdmnUseDiagnosticPacket
1.3.6.1.4.1.429.1.10.3.1.13
mandatory read-write
Description: Use diagnostic packets.Default=disable(1).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25AdmnItutClearLen
1.3.6.1.4.1.429.1.10.3.1.14
mandatory read-write
Description: Restrict the length of a CLEAR INDICATION to 5 bytes and a CLEAR CONFIRM to 3 bytes.Default=disable(1).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25AdmnBarDiagnosticPacket
1.3.6.1.4.1.429.1.10.3.1.15
mandatory read-write
Description: Bar diagnostic packets.Default=disable(1).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25AdmnDiscNzDiagnostic
1.3.6.1.4.1.429.1.10.3.1.16
mandatory read-write
Description: Discard all diagnostic packets on a non-zero LCN.Default=disable(1).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25AdmnAcceptHexAdd
1.3.6.1.4.1.429.1.10.3.1.17
mandatory read-write
Description: Allow DTE addresses to contain hexadecimal digits.Default=disable(1).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25AdmnBarNonPrivilegeListen
1.3.6.1.4.1.429.1.10.3.1.18
mandatory read-write
Description: Disallow a non-privileged user (i.e without superuser privilege) from listening for incoming calls.Default=enable(2).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25AdmnIntlAddrRecognition
1.3.6.1.4.1.429.1.10.3.1.19
mandatory read-write
Description: Determine whether outgoing international calls are to be accepted. The values and their interpretation are:1 - International calls are not distinguished.2 - The DNIC of the called DTE address is examined and compared to that held in the psdn_local members dnic1 and dnic2. A mismatch implies an international call.3 - International calls are distinguished by having a '1' prefix on the DTE address.4 - International calls are distinguished by having a '0' prefix on the DTE address.Default=notDistinguished(1).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = notDistinguished
(2) = examineDnic
(3) = prefix1
(4) = prefix0
MIB Information: ux25AdmnDnic
1.3.6.1.4.1.429.1.10.3.1.20
mandatory read-write
Description: This field contains the first four digits of DNIC and is only used when ux25AdmnIntlAddrRecognition is set to examineDnic(2). Note this field must contain exactly four BCD digits.Default=0000.
Settings: DisplayString
Syntax Ref. Type: SIZE
4 = 4
MIB Information: ux25AdmnIntlPrioritized
1.3.6.1.4.1.429.1.10.3.1.21
mandatory read-write
Description: Determine whether some prioritizing method is to used for international calls and is used in conjuction with ux25AdmnPrtyEncodeCtrl and ux25AdmnPrtyPktForced value.Default=disable(1).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25AdmnPrtyEncodeCtrl
1.3.6.1.4.1.429.1.10.3.1.22
mandatory read-write
Description: Describes how the priority request is to be encoded for this PSDN.Default=x2588(1).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = x2588
(2) = datapacPriority76
(3) = datapacTraffic80
MIB Information: ux25AdmnPrtyPktForcedVal
1.3.6.1.4.1.429.1.10.3.1.23
mandatory read-write
Description: If this entry is other than prioPktSz1(1) all priority call requests and incoming calls should have the associated packet size parameter forced to this value. Note that the actual packet size is 2 to the power of this parameter.Default=prioPktSz1(1).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = prioPktSz0
(5) = prioPktSz4
(6) = prioPktSz5
(7) = prioPktSz6
(8) = prioPktSz7
(9) = prioPktSz8
(10) = prioPktSz9
(11) = prioPktSz10
(12) = prioPktSz11
(13) = prioPktSz12
MIB Information: ux25AdmnSrcAddrCtrl
1.3.6.1.4.1.429.1.10.3.1.24
mandatory read-write
Description: Provide a means to override or set the calling address in outgoing call requests for this PSDN.Default=noSaCntrl(1).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = noSaCntrl
(2) = omitDte
(3) = useLocal
(4) = forceLocal
MIB Information: ux25AdmnDbitInAccept
1.3.6.1.4.1.429.1.10.3.1.25
mandatory read-write
Description: Defines the action to take when a Call Accept is received with the D-bit set and there is no local D-bit support.Default=clearCall(3).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = leaveDbit
(2) = zeroDbit
(3) = clearCall
MIB Information: ux25AdmnDbitOutAccept
1.3.6.1.4.1.429.1.10.3.1.26
mandatory read-write
Description: Defines the action to take when the remote user sends a Call Accept with the D-bit set when the local user did not request use of the D-bit.Default=clearCall(3).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = leaveDbit
(2) = zeroDbit
(3) = clearCall
MIB Information: ux25AdmnDbitInData
1.3.6.1.4.1.429.1.10.3.1.27
mandatory read-write
Description: Defines the action to take when a data packet is received with the D-bit set and the local user did not request use of the D-bit.Default=clearCall(3).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = leaveDbit
(2) = zeroDbit
(3) = clearCall
MIB Information: ux25AdmnDbitOutData
1.3.6.1.4.1.429.1.10.3.1.28
mandatory read-write
Description: Defines the action when the local user send a data packet with the D-bit set but the remote party has not indicated D-bit support.Default=clearCall(3).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = leaveDbit
(2) = zeroDbit
(3) = clearCall
MIB Information: ux25AdmnSubscriberTable
1.3.6.1.4.1.429.1.10.4
not-accessible
Description: Defines objects for the parameters of an X.25 interface which the administrator can read and set.
MIB Information: ux25AdmnSubscriberEntry
1.3.6.1.4.1.429.1.10.4.1
not-accessible
Description: Entries of ux25AdmnSubscriberTable.
MIB Information: ux25AdmnSubscriberIndex
1.3.6.1.4.1.429.1.10.4.1.1
mandatory read-only
Description: A unique value for each X.25 subnetwork entity in the chassis. The value of this object matches the value of the index of the corresponding X.25 subnetwork entity entry in the entity table of the chassis MIB.
Settings: INTEGER
MIB Information: ux25AdmnSubCugIaoa
1.3.6.1.4.1.429.1.10.4.1.2
mandatory read-write
Description: Specifies if this DTE subscribes to Closed User Groups with Incoming or Outgoing access.Default=enable(2).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25AdmnSubCugPref
1.3.6.1.4.1.429.1.10.4.1.3
mandatory read-write
Description: Specifies if this DTE subscribes to a Preferential Closed User Groups.Default=disable(1).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25AdmnSubCugoa
1.3.6.1.4.1.429.1.10.4.1.4
mandatory read-write
Description: Specifies if this DTE subscribes to Closed User Groups with Outgoing access.Default=disable(1).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25AdmnSubCugia
1.3.6.1.4.1.429.1.10.4.1.5
mandatory read-write
Description: Specifies whether or not this DTE subscribes to Closed User Groups with Incoming Access.Default=disable(1).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25AdmnCugFormat
1.3.6.1.4.1.429.1.10.4.1.6
mandatory read-write
Description: The maximum number of Closed User Groups that this DTE subscribes to. This will be one of two ranges: Basic (100 or fewer) or Extended (between 101 and 10000).Default=basic(1).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = basic
(2) = extended
MIB Information: ux25AdmnBarInCug
1.3.6.1.4.1.429.1.10.4.1.7
mandatory read-write
Description: Provides the means to force rejection of any incoming calls carrying the Closed User Group optional facility (which is necessary in some networks such as DDN. When enabled such calls will be rejected otherwise incoming Closed User Group facilities are ignored.Default=disable(1).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25AdmnSubExtended
1.3.6.1.4.1.429.1.10.4.1.8
mandatory read-write
Description: Subscribe to extended call packets (Window and Packet size negotiation is permitted).Default=enable(2).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25AdmnBarExtended
1.3.6.1.4.1.429.1.10.4.1.9
mandatory read-write
Description: Treat window and packet size negotiation in incoming packets as a procedure error.Default=disable(1).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25AdmnSubFstSelNoRstrct
1.3.6.1.4.1.429.1.10.4.1.10
mandatory read-write
Description: Subscribe to fast select with no restriction on response.Default=enable(2).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25AdmnSubFstSelWthRstrct
1.3.6.1.4.1.429.1.10.4.1.11
mandatory read-write
Description: Subscribe to fast select with restriction on response.Default=disable(1).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25AdmnAccptRvsChrgng
1.3.6.1.4.1.429.1.10.4.1.12
mandatory read-write
Description: Allow incoming calls to specify the reverse charging facility.Default=disable(1).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25AdmnSubLocChargePrevent
1.3.6.1.4.1.429.1.10.4.1.13
mandatory read-write
Description: Subscribe to local charging prevention.Default=disable(1).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25AdmnSubToaNpiFormat
1.3.6.1.4.1.429.1.10.4.1.14
mandatory read-write
Description: Subscribe to TOA/NPI Address Format.Default=disable(1).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25AdmnBarToaNpiFormat
1.3.6.1.4.1.429.1.10.4.1.15
mandatory read-write
Description: Bar incoming call set-up and clearing packets which use the TOA/NPI Address Format.Default=disable(1).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25AdmnSubNuiOverride
1.3.6.1.4.1.429.1.10.4.1.16
mandatory read-write
Description: Subscribe to NUI override.Deafult=disable(1).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25AdmnBarInCall
1.3.6.1.4.1.429.1.10.4.1.17
mandatory read-write
Description: Bar incoming calls.Default=disable(1).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25AdmnBarOutCall
1.3.6.1.4.1.429.1.10.4.1.18
mandatory read-write
Description: Bar outgoing calls.Default=disable(1).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25AdmnTimerTable
1.3.6.1.4.1.429.1.10.5
not-accessible
Description: Defines objects for the parameters of an X.25 interface which the administrator can read and set.
MIB Information: ux25AdmnTimerEntry
1.3.6.1.4.1.429.1.10.5.1
not-accessible
Description: Entries of ux25AdmnTimerTable.
MIB Information: ux25AdmnTimerIndex
1.3.6.1.4.1.429.1.10.5.1.1
mandatory read-only
Description: A unique value for each X.25 subnetwork entity in the chassis. The value of this object matches the value of the index of the corresponding X.25 subnetwork entity entry in the entity table of the chassis MIB.
Settings: INTEGER
MIB Information: ux25AdmnAckDelay
1.3.6.1.4.1.429.1.10.5.1.2
mandatory read-write
Description: The maximum number of ticks (0.1 second units) over which a pending acknowledgement is withheld.Default=5.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 32000
MIB Information: ux25AdmnRstrtTime
1.3.6.1.4.1.429.1.10.5.1.3
mandatory read-write
Description: The number of ticks (0.1 second units) for the DTE timer parameter T20 the Restart Request Response Timer.Default=1800.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 32000
MIB Information: ux25AdmnCallTime
1.3.6.1.4.1.429.1.10.5.1.4
mandatory read-write
Description: The number of ticks (0.1 second units) for the DTE timer parameter T21 the Call Request Response Timer.Default=2000.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 32000
MIB Information: ux25AdmnRstTime
1.3.6.1.4.1.429.1.10.5.1.5
mandatory read-write
Description: The number of ticks (0.1 second units) for the DTE timer parameter T22 the Reset Request Response Timer.Default=1800.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 32000
MIB Information: ux25AdmnClrTime
1.3.6.1.4.1.429.1.10.5.1.6
mandatory read-write
Description: The number of ticks (0.1 second units) for the DTE timer parameter T23 the Clear Request Response Timer.Default=1800.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 32000
MIB Information: ux25AdmnWinStatTime
1.3.6.1.4.1.429.1.10.5.1.7
mandatory read-write
Description: Related but does not correspond exactly to the DTE Window Status Transmission Timer T24. Specifies the number of ticks (0.1 second units) for the maximum time that acknowledgments of data received from the remote transmitter will be witheld. At timer expiration any witheld acknowledgments will be carried by a X.25 level 3 RNR packet.Default=750.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 32000
MIB Information: ux25AdmnWinRotTime
1.3.6.1.4.1.429.1.10.5.1.8
mandatory read-write
Description: The number of ticks (0.1 second units) for the DTE timer parameter T25 the Window Rotation Timer.Default=1500.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 32000
MIB Information: ux25AdmnIntrptTime
1.3.6.1.4.1.429.1.10.5.1.9
mandatory read-write
Description: The number of ticks (0.1 second units) for the DTE timer parameter T26 the Interrupt Response Timer.Default=1800.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 32000
MIB Information: ux25AdmnIdleValue
1.3.6.1.4.1.429.1.10.5.1.10
mandatory read-write
Description: The number of ticks (0.1 second units) during which a link level connection associated with no connections will be maintained. If the link is to a WAN then this value should be zero (infinity). This timer is only used with X.25 on a LAN.Default=0.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 32000
MIB Information: ux25AdmnConnectValue
1.3.6.1.4.1.429.1.10.5.1.11
mandatory read-write
Description: Specifies the number of ticks (0.1 second units) over which the DTE/DCE resolution phase be completely implemented in order to prevent the unlikely event that two packet level entities cannot resolve their DTE/DCE nature. When this expires the link connection will be disconnected and all pending connections aborted.Default=2000.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 32000
MIB Information: ux25AdmnRstrtCnt
1.3.6.1.4.1.429.1.10.5.1.12
mandatory read-write
Description: The number of ticks (0.1 second units) for the DTE Restart Request Retransmission Count.Default=1.
Settings: INTEGER
Syntax Ref. Type: RANGE
1 = 255
MIB Information: ux25AdmnRstCnt
1.3.6.1.4.1.429.1.10.5.1.13
mandatory read-write
Description: The number of ticks (0.1 second units) for the DTE Reset Request Retransmission Count.Default=1.
Settings: INTEGER
Syntax Ref. Type: RANGE
1 = 255
MIB Information: ux25AdmnClrCnt
1.3.6.1.4.1.429.1.10.5.1.14
mandatory read-write
Description: The number of ticks (0.1 second units) for the DTE Clear Request Retransmission Count.Default=1.
Settings: INTEGER
Syntax Ref. Type: RANGE
1 = 255
MIB Information: ux25AdmnLocalDelay
1.3.6.1.4.1.429.1.10.5.1.15
mandatory read-write
Description: The transit delay (in 0.1 second units) attributed to internal processing.Default=5.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 32000
MIB Information: ux25AdmnAccessDelay
1.3.6.1.4.1.429.1.10.5.1.16
mandatory read-write
Description: The transit delay (in 0.1 second units) attributed to the effect of the line transmission rate.Default=5.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 32000
MIB Information: ux25OperChannelTable
1.3.6.1.4.1.429.1.10.6
not-accessible
Description: Defines objects that report the current parameters used by a running interface. These objects are read only.
MIB Information: ux25OperChannelEntry
1.3.6.1.4.1.429.1.10.6.1
not-accessible
Description: Entries of ux25OperChannelTable.
MIB Information: ux25OperChannelIndex
1.3.6.1.4.1.429.1.10.6.1.1
mandatory read-only
Settings: INTEGER
MIB Information: ux25OperNetMode
1.3.6.1.4.1.429.1.10.6.1.2
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = x25Llc
(2) = x2588
(3) = x2584
(4) = x2580
(5) = pss
(6) = austpac
(7) = datapac
(8) = ddn
(9) = telenet
(10) = transpac
(11) = tymnet
(12) = datexP
(13) = ddxP
(14) = venusP
(15) = accunet
(16) = itapac
(17) = datapak
(18) = datanet
(19) = dcs
(20) = telepac
(21) = fDatapac
(22) = finpac
(23) = pacnet
(24) = luxpac
MIB Information: ux25OperProtocolVersion
1.3.6.1.4.1.429.1.10.6.1.3
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = x25ver80
(2) = x25ver84
(3) = x25ver88
MIB Information: ux25OperInterfaceMode
1.3.6.1.4.1.429.1.10.6.1.4
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = dceMode
(2) = dteMode
(3) = dxeMode
MIB Information: ux25OperLowestPVCVal
1.3.6.1.4.1.429.1.10.6.1.5
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 4095
MIB Information: ux25OperHighestPVCVal
1.3.6.1.4.1.429.1.10.6.1.6
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 4095
MIB Information: ux25OperChannelLIC
1.3.6.1.4.1.429.1.10.6.1.7
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 4095
MIB Information: ux25OperChannelHIC
1.3.6.1.4.1.429.1.10.6.1.8
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 4095
MIB Information: ux25OperChannelLTC
1.3.6.1.4.1.429.1.10.6.1.9
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 4095
MIB Information: ux25OperChannelHTC
1.3.6.1.4.1.429.1.10.6.1.10
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 4095
MIB Information: ux25OperChannelLOC
1.3.6.1.4.1.429.1.10.6.1.11
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 4095
MIB Information: ux25OperChannelHOC
1.3.6.1.4.1.429.1.10.6.1.12
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 4095
MIB Information: ux25OperClassTable
1.3.6.1.4.1.429.1.10.7
not-accessible
Description: Defines objects that report the current parameters used by a running interface. These objects are read only.
MIB Information: ux25OperClassEntry
1.3.6.1.4.1.429.1.10.7.1
not-accessible
Description: Entries of ux25OperTable.
MIB Information: ux25OperClassIndex
1.3.6.1.4.1.429.1.10.7.1.1
mandatory read-only
Settings: INTEGER
MIB Information: ux25OperLocMaxThruPutClass
1.3.6.1.4.1.429.1.10.7.1.2
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = tcReserved0
(2) = tcReserved1
(3) = tcReserved2
(4) = tc75
(5) = tc150
(6) = tc300
(7) = tc600
(8) = tc1200
(9) = tc2400
(10) = tc4800
(11) = tc9600
(12) = tc19200
(13) = tc48000
(14) = tcReserved13
(15) = tcReserved14
(16) = tcReserved15
MIB Information: ux25OperRemMaxThruPutClass
1.3.6.1.4.1.429.1.10.7.1.3
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = tcReserved0
(2) = tcReserved1
(3) = tcReserved2
(4) = tc75
(5) = tc150
(6) = tc300
(7) = tc600
(8) = tc1200
(9) = tc2400
(10) = tc4800
(11) = tc9600
(12) = tc19200
(13) = tc48000
(14) = tcReserved13
(15) = tcReserved14
(16) = tcReserved15
MIB Information: ux25OperLocDefThruPutClass
1.3.6.1.4.1.429.1.10.7.1.4
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = tcReserved0
(2) = tcReserved1
(3) = tcReserved2
(4) = tc75
(5) = tc150
(6) = tc300
(7) = tc600
(8) = tc1200
(9) = tc2400
(10) = tc4800
(11) = tc9600
(12) = tc19200
(13) = tc48000
(14) = tcReserved13
(15) = tcReserved14
(16) = tcReserved15
MIB Information: ux25OperRemDefThruPutClass
1.3.6.1.4.1.429.1.10.7.1.5
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = tcReserved0
(2) = tcReserved1
(3) = tcReserved2
(4) = tc75
(5) = tc150
(6) = tc300
(7) = tc600
(8) = tc1200
(9) = tc2400
(10) = tc4800
(11) = tc9600
(12) = tc19200
(13) = tc48000
(14) = tcReserved13
(15) = tcReserved14
(16) = tcReserved15
MIB Information: ux25OperLocMinThruPutClass
1.3.6.1.4.1.429.1.10.7.1.6
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = tcReserved0
(2) = tcReserved1
(3) = tcReserved2
(4) = tc75
(5) = tc150
(6) = tc300
(7) = tc600
(8) = tc1200
(9) = tc2400
(10) = tc4800
(11) = tc9600
(12) = tc19200
(13) = tc48000
(14) = tcReserved13
(15) = tcReserved14
(16) = tcReserved15
MIB Information: ux25OperRemMinThruPutClass
1.3.6.1.4.1.429.1.10.7.1.7
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = tcReserved0
(2) = tcReserved1
(3) = tcReserved2
(4) = tc75
(5) = tc150
(6) = tc300
(7) = tc600
(8) = tc1200
(9) = tc2400
(10) = tc4800
(11) = tc9600
(12) = tc19200
(13) = tc48000
(14) = tcReserved13
(15) = tcReserved14
(16) = tcReserved15
MIB Information: ux25OperThclassNegToDef
1.3.6.1.4.1.429.1.10.7.1.8
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25OperThclassType
1.3.6.1.4.1.429.1.10.7.1.9
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = noTcType
(2) = loNibble
(3) = highNibble
(4) = bothNibbles
MIB Information: ux25OperThclassWinMap
1.3.6.1.4.1.429.1.10.7.1.10
mandatory read-only
Settings: DisplayString
Syntax Ref. Type: SIZE
31 = 63
MIB Information: ux25OperThclassPackMap
1.3.6.1.4.1.429.1.10.7.1.11
mandatory read-only
Settings: DisplayString
Syntax Ref. Type: SIZE
31 = 47
MIB Information: ux25OperPacketTable
1.3.6.1.4.1.429.1.10.8
not-accessible
Description: Defines objects that report the current parameters used by a running interface. These objects are read only.
MIB Information: ux25OperPacketEntry
1.3.6.1.4.1.429.1.10.8.1
not-accessible
Description: Entries of ux25OperPacketTable.
MIB Information: ux25OperPacketIndex
1.3.6.1.4.1.429.1.10.8.1.1
mandatory read-only
Settings: INTEGER
MIB Information: ux25OperPktSequencing
1.3.6.1.4.1.429.1.10.8.1.2
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(16) = pktSeq8
(32) = pktSeq128
MIB Information: ux25OperLocMaxPktSize
1.3.6.1.4.1.429.1.10.8.1.3
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(7) = maxPktSz128
(8) = maxPktSz256
(9) = maxPktSz512
MIB Information: ux25OperRemMaxPktSize
1.3.6.1.4.1.429.1.10.8.1.4
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(7) = maxPktSz128
(8) = maxPktSz256
(9) = maxPktSz512
MIB Information: ux25OperLocDefPktSize
1.3.6.1.4.1.429.1.10.8.1.5
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(4) = defPktSz16
(5) = defPktSz32
(6) = defPktSz64
(7) = defPktSz128
(8) = defPktSz256
(9) = defPktSz512
MIB Information: ux25OperRemDefPktSize
1.3.6.1.4.1.429.1.10.8.1.6
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(4) = defPktSz16
(5) = defPktSz32
(6) = defPktSz64
(7) = defPktSz128
(8) = defPktSz256
(9) = defPktSz512
MIB Information: ux25OperLocMaxWinSize
1.3.6.1.4.1.429.1.10.8.1.7
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: RANGE
2 = 127
MIB Information: ux25OperRemMaxWinSize
1.3.6.1.4.1.429.1.10.8.1.8
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: RANGE
2 = 127
MIB Information: ux25OperLocDefWinSize
1.3.6.1.4.1.429.1.10.8.1.9
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: RANGE
1 = 127
MIB Information: ux25OperRemDefWinSize
1.3.6.1.4.1.429.1.10.8.1.10
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: RANGE
1 = 127
MIB Information: ux25OperMaxNSDULimit
1.3.6.1.4.1.429.1.10.8.1.11
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 32000
MIB Information: ux25OperAccNoDiagnostic
1.3.6.1.4.1.429.1.10.8.1.12
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25OperUseDiagnosticPacket
1.3.6.1.4.1.429.1.10.8.1.13
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25OperItutClearLen
1.3.6.1.4.1.429.1.10.8.1.14
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25OperBarDiagnosticPacket
1.3.6.1.4.1.429.1.10.8.1.15
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25OperDiscNzDiagnostic
1.3.6.1.4.1.429.1.10.8.1.16
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25OperAcceptHexAdd
1.3.6.1.4.1.429.1.10.8.1.17
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25OperBarNonPrivilegeListen
1.3.6.1.4.1.429.1.10.8.1.18
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25OperIntlAddrRecognition
1.3.6.1.4.1.429.1.10.8.1.19
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = notDistinguished
(2) = examineDnic
(3) = prefix1
(4) = prefix0
MIB Information: ux25OperDnic
1.3.6.1.4.1.429.1.10.8.1.20
mandatory read-only
Settings: DisplayString
Syntax Ref. Type: SIZE
4 = 4
MIB Information: ux25OperIntlPrioritized
1.3.6.1.4.1.429.1.10.8.1.21
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25OperPrtyEncodeCtrl
1.3.6.1.4.1.429.1.10.8.1.22
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = x2588
(2) = datapacPriority76
(3) = datapacTraffic80
MIB Information: ux25OperPrtyPktForcedVal
1.3.6.1.4.1.429.1.10.8.1.23
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = prioPktSz0
(5) = prioPktSz4
(6) = prioPktSz5
(7) = prioPktSz6
(8) = prioPktSz7
(9) = prioPktSz8
(10) = prioPktSz9
(11) = prioPktSz10
(12) = prioPktSz11
(13) = prioPktSz12
MIB Information: ux25OperSrcAddrCtrl
1.3.6.1.4.1.429.1.10.8.1.24
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = noSaCntrl
(2) = omitDte
(3) = useLocal
(4) = forceLocal
MIB Information: ux25OperDbitInAccept
1.3.6.1.4.1.429.1.10.8.1.25
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = leaveDbit
(2) = zeroDbit
(3) = clearCall
MIB Information: ux25OperDbitOutAccept
1.3.6.1.4.1.429.1.10.8.1.26
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = leaveDbit
(2) = zeroDbit
(3) = clearCall
MIB Information: ux25OperDbitInData
1.3.6.1.4.1.429.1.10.8.1.27
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = leaveDbit
(2) = zeroDbit
(3) = clearCall
MIB Information: ux25OperDbitOutData
1.3.6.1.4.1.429.1.10.8.1.28
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = leaveDbit
(2) = zeroDbit
(3) = clearCall
MIB Information: ux25OperSubscriberTable
1.3.6.1.4.1.429.1.10.9
not-accessible
Description: Defines objects that report the current parameters used by a running interface. These objects are read only.
MIB Information: ux25OperSubscriberEntry
1.3.6.1.4.1.429.1.10.9.1
not-accessible
Description: Entries of ux25OperSubscriberTable.
MIB Information: ux25OperSubscriberIndex
1.3.6.1.4.1.429.1.10.9.1.1
mandatory read-only
Settings: INTEGER
MIB Information: ux25OperSubCugIaoa
1.3.6.1.4.1.429.1.10.9.1.2
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25OperSubCugPref
1.3.6.1.4.1.429.1.10.9.1.3
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25OperSubCugoa
1.3.6.1.4.1.429.1.10.9.1.4
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25OperSubCugia
1.3.6.1.4.1.429.1.10.9.1.5
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25OperCugFormat
1.3.6.1.4.1.429.1.10.9.1.6
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = basic
(2) = extended
MIB Information: ux25OperBarInCug
1.3.6.1.4.1.429.1.10.9.1.7
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25OperSubExtended
1.3.6.1.4.1.429.1.10.9.1.8
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25OperBarExtended
1.3.6.1.4.1.429.1.10.9.1.9
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25OperSubFstSelNoRstrct
1.3.6.1.4.1.429.1.10.9.1.10
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25OperSubFstSelWthRstrct
1.3.6.1.4.1.429.1.10.9.1.11
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25OperAccptRvsChrgng
1.3.6.1.4.1.429.1.10.9.1.12
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25OperSubLocChargePrevent
1.3.6.1.4.1.429.1.10.9.1.13
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25OperSubToaNpiFormat
1.3.6.1.4.1.429.1.10.9.1.14
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25OperBarToaNpiFormat
1.3.6.1.4.1.429.1.10.9.1.15
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25OperSubNuiOverride
1.3.6.1.4.1.429.1.10.9.1.16
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25OperBarInCall
1.3.6.1.4.1.429.1.10.9.1.17
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25OperBarOutCall
1.3.6.1.4.1.429.1.10.9.1.18
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: ux25OperTimerTable
1.3.6.1.4.1.429.1.10.10
not-accessible
Description: Defines objects that report the current parameters used by a running interface. These objects are read only.
MIB Information: ux25OperTimerEntry
1.3.6.1.4.1.429.1.10.10.1
not-accessible
Description: Entries of ux25OperTimerTable.
MIB Information: ux25OperTimerIndex
1.3.6.1.4.1.429.1.10.10.1.1
mandatory read-only
Settings: INTEGER
MIB Information: ux25OperAckDelay
1.3.6.1.4.1.429.1.10.10.1.2
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 32000
MIB Information: ux25OperRstrtTime
1.3.6.1.4.1.429.1.10.10.1.3
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 32000
MIB Information: ux25OperCallTime
1.3.6.1.4.1.429.1.10.10.1.4
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 32000
MIB Information: ux25OperRstTime
1.3.6.1.4.1.429.1.10.10.1.5
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 32000
MIB Information: ux25OperClrTime
1.3.6.1.4.1.429.1.10.10.1.6
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 32000
MIB Information: ux25OperWinStatTime
1.3.6.1.4.1.429.1.10.10.1.7
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 32000
MIB Information: ux25OperWinRotTime
1.3.6.1.4.1.429.1.10.10.1.8
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 32000
MIB Information: ux25OperIntrptTime
1.3.6.1.4.1.429.1.10.10.1.9
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 32000
MIB Information: ux25OperIdleValue
1.3.6.1.4.1.429.1.10.10.1.10
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 32000
MIB Information: ux25OperConnectValue
1.3.6.1.4.1.429.1.10.10.1.11
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 32000
MIB Information: ux25OperRstrtCnt
1.3.6.1.4.1.429.1.10.10.1.12
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: RANGE
1 = 255
MIB Information: ux25OperRstCnt
1.3.6.1.4.1.429.1.10.10.1.13
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: RANGE
1 = 255
MIB Information: ux25OperClrCnt
1.3.6.1.4.1.429.1.10.10.1.14
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: RANGE
1 = 255
MIB Information: ux25OperLocalDelay
1.3.6.1.4.1.429.1.10.10.1.15
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 32000
MIB Information: ux25OperAccessDelay
1.3.6.1.4.1.429.1.10.10.1.16
mandatory read-only
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 32000
MIB Information: ux25StatTable
1.3.6.1.4.1.429.1.10.11
not-accessible
Description: Defines objects that report operational statistics for an X.25 interface.
MIB Information: ux25StatEntry
1.3.6.1.4.1.429.1.10.11.1
not-accessible
Description: Entries of ux25StatTable.
MIB Information: ux25StatIndex
1.3.6.1.4.1.429.1.10.11.1.1
mandatory read-only
Description: A unique value for each X.25 subnetwork entity in the chassis. The value of this object matches the value of the index of the corresponding X.25 subnetwork entity entry in the entity table of the chassis MIB.
Settings: INTEGER
MIB Information: ux25StatCallsRcvd
1.3.6.1.4.1.429.1.10.11.1.2
mandatory read-only
Description: Number of incoming calls.
Settings: INTEGER
MIB Information: ux25StatCallsSent
1.3.6.1.4.1.429.1.10.11.1.3
mandatory read-only
Description: Number of outgoing calls.
Settings: INTEGER
MIB Information: ux25StatCallsRcvdEstab
1.3.6.1.4.1.429.1.10.11.1.4
mandatory read-only
Description: Number of incoming calls established.
Settings: INTEGER
MIB Information: ux25StatCallsSentEstab
1.3.6.1.4.1.429.1.10.11.1.5
mandatory read-only
Description: Number of outgoing calls established.
Settings: INTEGER
MIB Information: ux25StatDataPktsRcvd
1.3.6.1.4.1.429.1.10.11.1.6
mandatory read-only
Description: Number of data packets received.
Settings: INTEGER
MIB Information: ux25StatDataPktsSent
1.3.6.1.4.1.429.1.10.11.1.7
mandatory read-only
Description: Number of data packets sent.
Settings: INTEGER
MIB Information: ux25StatRestartsRcvd
1.3.6.1.4.1.429.1.10.11.1.8
mandatory read-only
Description: Number of restarts received.
Settings: INTEGER
MIB Information: ux25StatRestartsSent
1.3.6.1.4.1.429.1.10.11.1.9
mandatory read-only
Description: Number of restarts sent.
Settings: INTEGER
MIB Information: ux25StatRcvrNotRdyRcvd
1.3.6.1.4.1.429.1.10.11.1.10
mandatory read-only
Description: Number of receiver not ready received.
Settings: INTEGER
MIB Information: ux25StatRcvrNotRdySent
1.3.6.1.4.1.429.1.10.11.1.11
mandatory read-only
Description: Number of receiver not ready sent.
Settings: INTEGER
MIB Information: ux25StatRcvrRdyRcvd
1.3.6.1.4.1.429.1.10.11.1.12
mandatory read-only
Description: Number of receiver ready received.
Settings: INTEGER
MIB Information: ux25StatRcvrRdySent
1.3.6.1.4.1.429.1.10.11.1.13
mandatory read-only
Description: Number of receiver ready sent.
Settings: INTEGER
MIB Information: ux25StatResetsRcvd
1.3.6.1.4.1.429.1.10.11.1.14
mandatory read-only
Description: Number of resets received.
Settings: INTEGER
MIB Information: ux25StatResetsSent
1.3.6.1.4.1.429.1.10.11.1.15
mandatory read-only
Description: Number of resets sent.
Settings: INTEGER
MIB Information: ux25StatDiagPktsRcvd
1.3.6.1.4.1.429.1.10.11.1.16
mandatory read-only
Description: Number of diagnostic packets received.
Settings: INTEGER
MIB Information: ux25StatDiagPktsSent
1.3.6.1.4.1.429.1.10.11.1.17
mandatory read-only
Description: Number of diagnostic packets sent.
Settings: INTEGER
MIB Information: ux25StatIntrptPktsRcvd
1.3.6.1.4.1.429.1.10.11.1.18
mandatory read-only
Description: Number of interrupt packets received.
Settings: INTEGER
MIB Information: ux25StatIntrptPktsSent
1.3.6.1.4.1.429.1.10.11.1.19
mandatory read-only
Description: Number of interrupt packets sent.
Settings: INTEGER
MIB Information: ux25StatPVCsInDatTrnsfrState
1.3.6.1.4.1.429.1.10.11.1.20
mandatory read-only
Description: Number of PVCs in Data Transfer State.
Settings: INTEGER
MIB Information: ux25StatSVCsInDatTrnsfrState
1.3.6.1.4.1.429.1.10.11.1.21
mandatory read-only
Description: Number of SVCs in Data Transfer State.
Settings: INTEGER
Copyright © 2000 3Com Corporation.