|
|
|
|
MIB Information: uchasCmd
1.3.6.1.4.1.429.1.1.7
MIB Information: uchasCmdTable
1.3.6.1.4.1.429.1.1.7.1
not-accessible
Description: The Chassis Command table contains an entry for each of the NIC and NAC slots in the chassis. It provides a means through which to take specific actions on one or more devices in the chassis at a card level. Device specific commands are not included here but rather in the specific MIB used to manage the device.
MIB Information: uchasCmdEntry
1.3.6.1.4.1.429.1.1.7.1.1
not-accessible
Description: There is one entry in this table for each row in uchasSlotTable.
MIB Information: uchasCmdSlotIndex
1.3.6.1.4.1.429.1.1.7.1.1.1
mandatory read-only
Description: This index uniquely identifies the slot to which the command being written is to take place. Values of uchasCmdSlotIndex correspond to values used to index uchasSlotTable.
Settings: INTEGER
MIB Information: uchasCmdMgtStationId
1.3.6.1.4.1.429.1.1.7.1.1.2
mandatory read-write
Description: This object is a generic read-write variable that a Management Station (MS) can use to guarantee that the results from a given command are the results of a command issued by that specific MS. Each MS must SET a unique value to this object when doing commands and GET the value of this object together with uchasCmdReqId and uchasCmdResult to detect interference from other MSs.
Settings: OCTET STRING
Syntax Ref. Type: SIZE
0 = 8
MIB Information: uchasCmdReqId
1.3.6.1.4.1.429.1.1.7.1.1.3
mandatory read-only
Description: Ths object contains the value of the request-id field in the SNMP PDU which invoked the current or most recent command on the device in the specified slot of the chassis. If the request-id is unknown or undefined this value contains the value zero.
Settings: INTEGER
MIB Information: uchasCmdFunction
1.3.6.1.4.1.429.1.1.7.1.1.4
mandatory read-write
Description: A control variable used to start and stop operator-initiated commands. A command is initiated by setting this object to a value other than noCommand(1). When the value noCommand(1) is written to this object no action is taken unless a command is in progress in which case the command is aborted.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = noCommand
(2) = removeFromService
(3) = restoreToService
(4) = hardwareReset
(5) = softwareDownload
(6) = softwareDownload2
MIB Information: uchasCmdForce
1.3.6.1.4.1.429.1.1.7.1.1.5
mandatory read-write
Description: In some cases the devices in the chassis may be in a state such that certain commands could adversely affect connections or other device specific operations. In such cases a command with uchasCmdForce set to noForce will result in a warning. If the operator elects to ignore such warnings uchasCmdForce can be set to force in the command request and the command will be carried out regardless of its potentially hazzardous effects.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = force
(2) = noForce
MIB Information: uchasCmdParam
1.3.6.1.4.1.429.1.1.7.1.1.6
mandatory read-write
Description: This object contains parameters that are specific to the particular command being issued. In some cases there will be no additional parameters required.
Settings: OCTET STRING
Syntax Ref. Type: SIZE
0 = 24
MIB Information: uchasCmdResult
1.3.6.1.4.1.429.1.1.7.1.1.7
mandatory read-only
Description: This object contains the result of the most recently requested test or the value none(1) if not commands have been requested since the last reset. Note that this facility provides no provision for saving the results of one command when starting another as could be required if used by multiple managers concurrently.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = none
(2) = success
(3) = inProgress
(4) = notSupported
(5) = unAbleToRun
(6) = aborted
(7) = failed
MIB Information: uchasCmdCode
1.3.6.1.4.1.429.1.1.7.1.1.8
mandatory read-only
Description: The value of this object upon command completion indicates a further description of what went wrong if the command was unsuccessful. This object is also used as an indication of the in progress status of the software download command.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = noError
(2) = unable
(6) = unrecognizedCommand
(8) = slotEmpty
(12) = noResponse
(14) = connected
(20) = unsupportedCommand
(21) = nonManagedDevice
(22) = deviceDisabled
(58) = userInterfaceActive
(61) = badFlashRomID
(62) = badFlashVoltage
(63) = flashEraseError
(64) = eraseSequenceError
(65) = eraseExecutionError
(66) = receiveBufferOverflow
(67) = badAddressInData
(68) = badProgramVoltage
(69) = programmingDataError
(70) = programCodeError
(71) = invalidCodeError
(72) = romCrcBad
(73) = pendingSoftwareDownload
(74) = ramCrcBad
(75) = invalidRomId
(76) = sdlTrigger
(77) = downloadingSdlFile
(78) = crcTestingSdlFile
(79) = queryWorkSpaceSize
(80) = executeLoadedProgram
(81) = erasingFlash
(82) = downloadingNacFile
(83) = resetingNac
(84) = cardIdMismatch
(85) = cardIdUnknown
(86) = tftpTimeout
(87) = flashEraseTimeout
(88) = invalidFileHeader
(113) = pendingSdl2
(118) = osShutdownTimeout
(119) = pendOsShutdown
(120) = osShutdownFailed
Copyright © 2000 3Com Corporation.