|
|
|
|
MIB Information: hdmICc
1.3.6.1.4.1.429.1.22.10
MIB Information: hdmICcTable
1.3.6.1.4.1.429.1.22.10.1
not-accessible
Description: A table containing the call control parameters for each modem in the chassis.
MIB Information: hdmICcEntry
1.3.6.1.4.1.429.1.22.10.1.1
not-accessible
Description: Call control parameters for an ISDN modem. These define the sequence of operation related to how a call is negotiated.
MIB Information: hdmICcIndex
1.3.6.1.4.1.429.1.22.10.1.1.1
mandatory read-only
Description: The index which uniquely identifies the modem to which this entry is applicable. The value corresponds to the value of the index to the entity table in the chassis MIB that corresponds to the same modem.
Settings: INTEGER
MIB Information: hdmICcIndex2
1.3.6.1.4.1.429.1.22.10.1.1.2
mandatory read-only
Description: Secondary Index into the ISDN Call Control table. This index is the value from the chassis mib entity relation table that is applicable for a particular modem.
Settings: INTEGER
MIB Information: hdmICcRateAdapV110
1.3.6.1.4.1.429.1.22.10.1.1.3
mandatory read-write
Description: This object enables V110 rate adaption corresponds to S register S67 bit 0. Default = enabled(2)
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: hdmICcFixedNtwkRate
1.3.6.1.4.1.429.1.22.10.1.1.4
mandatory read-write
Description: This object sets the fixed network rate. This object correspond to S register S67 bit 1. Default = notForced(1)
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = notForced
(2) = forceNetworkRate
MIB Information: hdmICcNetworkRate
1.3.6.1.4.1.429.1.22.10.1.1.5
mandatory read-write
Description: This object sets the Network rate speed. This object corresponds to the modem S register S67 bit 2. Default = kbps56(1)
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = kbps56
(2) = kbps64
MIB Information: hdmICcBcLinkDly
1.3.6.1.4.1.429.1.22.10.1.1.6
mandatory read-write
Description: This object enable a 45 - 65 second link delay. This object corresponds to the S register S67 bit 4. Default = noDelay(1)
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = noDelay
(2) = delay
MIB Information: hdmICcDisAnlgOvrDig
1.3.6.1.4.1.429.1.22.10.1.1.7
mandatory read-write
Description: This object is used to set S register S68 bit 0 which does not allow analog calls over digital data connection. Default = enable(1)
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = enable
(2) = disable
MIB Information: hdmICcDisAsyncPPP
1.3.6.1.4.1.429.1.22.10.1.1.8
mandatory read-write
Description: This object is used to disable/enable async PPP/ sync PPP conversion. This object corresponds to S register S68 bit 4. Default = enable(1)
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = enable
(2) = disable
MIB Information: hdmICcDisX75
1.3.6.1.4.1.429.1.22.10.1.1.9
mandatory read-write
Description: This object is used to disable/enable X75. This object corresponds to S register S68 bit 5. Default = enable(1)
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = enable
(2) = disable
MIB Information: hdmICcStarV2
1.3.6.1.4.1.429.1.22.10.1.1.10
mandatory read-write
Description: This object is used to set the data mode of the modem and is equivalent to *V2 = x AT command. Default = autodetect(1)
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = autodetect
(2) = v120rateAdapOnly
(3) = v110rateAdapOnly
(4) = modemOrFaxOnly
(5) = clearChannelSync
(6) = asyncSyncPPPconv
(7) = x75
MIB Information: hdmICcStarU1
1.3.6.1.4.1.429.1.22.10.1.1.11
mandatory read-write
Description: This object is used to set the originate HDLC protocols of the modem and is equivalent to *U1 = x AT command. Default = v120(2)
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = none
(2) = v120
(3) = x75
(4) = ppp
MIB Information: hdmICcStarU2
1.3.6.1.4.1.429.1.22.10.1.1.12
mandatory read-write
Description: This object is used to set the originate Non-HDLC protocols of the modem and is equivalent to *U2 = x AT command. Default = none(1)
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = none
(2) = v110
MIB Information: hdmICcStarU3
1.3.6.1.4.1.429.1.22.10.1.1.13
mandatory read-write
Description: This object is used to set the originate Analog modem/fax data mode of the modem and is equivalent to *U3 = x AT command. Default = analogModemFax(2)
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = none
(2) = analogModemFax
MIB Information: hdmICcV120
1.3.6.1.4.1.429.1.22.10.1.1.14
mandatory read-write
Description: This object is used to Enable/Disable V120. This object corresponds to S register 68 bit 4. Default=enable(1).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = enable
(2) = disable
MIB Information: hdmICcFrameSize
1.3.6.1.4.1.429.1.22.10.1.1.15
mandatory read-write
Description: This object is used to set the frame size for X75. Default = 2048.
Settings: INTEGER
Syntax Ref. Type: RANGE
1 = 2048
MIB Information: hdmICcWindowSize
1.3.6.1.4.1.429.1.22.10.1.1.16
mandatory read-write
Description: This object is used to set the window size of X75. Default=2.
Settings: INTEGER
Syntax Ref. Type: RANGE
1 = 7
Copyright © 2000 3Com Corporation.