|
|
|
|
MIB Information: hdviCfg
1.3.6.1.4.1.429.1.29.1
MIB Information: hdviCfgTable
1.3.6.1.4.1.429.1.29.1.1
not-accessible
Description: A table containing the configuration parameters for the Hiper DSP Entities.
MIB Information: hdviCfgEntry
1.3.6.1.4.1.429.1.29.1.1.1
not-accessible
Description: Configuration parameters for the Hiper DSP CARD.
MIB Information: hdviCfgIndex
1.3.6.1.4.1.429.1.29.1.1.1.1
mandatory read-only
Description: The index which uniquely identifies the Hiper DSP CARD to which this entry is applicable.
Settings: INTEGER
MIB Information: hdviCfgMaxJitterBufSize
1.3.6.1.4.1.429.1.29.1.1.1.2
obsolete read-write
Description: This object represents the maximum size of the jitter buffer in 5 ms increments. Same as S86. The HiPerDSP will map the value of this parameter to an integer number of audio packets that most closely approximates the specified jitter buffering.The usage of the object has changed and is no longer meaningful. Its purpose is best represented by hdviCfgMaxJitterCompensation.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 100
MIB Information: hdviCfgSilenceSuppress
1.3.6.1.4.1.429.1.29.1.1.1.3
obsolete read-only
Description: This parameter is used to enable Voice Detector/Silence suppression in the DSP. ( S Register S87). This object is obsolete. It is now configured through the Gateway card.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: hdviCfgTranscoderBitRate
1.3.6.1.4.1.429.1.29.1.1.1.4
mandatory read-only
Description: This parameter sets the transcoder for data generated by the DSP. (S register S88).
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = g723-1-6-3-KBPS
(2) = g723-1-5-3-KBPS
(3) = g729A-8-0-KBPS
(4) = g711-uLaw-64-KBPS
(5) = g711-aLaw-64-KBPS
MIB Information: hdviCfgComfNoise
1.3.6.1.4.1.429.1.29.1.1.1.5
obsolete read-write
Description: This parameter enables the White Noise to PSTN when no audio is received from LAN. This object is obsolete.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: hdviCfgITGTxGainAtten
1.3.6.1.4.1.429.1.29.1.1.1.6
mandatory read-write
Description: This object represents whether the ITGTxLevel represents gain or attenuation. 0 means gain and 1 means attenuation. Same as S91.7
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = gain
(2) = attenuation
MIB Information: hdviCfgITGTxLevel
1.3.6.1.4.1.429.1.29.1.1.1.7
mandatory read-write
Description: This object represents the gain/attenuation(in dB) to be applied to the outgoing PCM signal. This level represents the amount of gain if ITGTxGainAttenuation is set to Gain(0). This level represents the amount of attenuation if ITGTxGainAttenuation is set to Attenuation(1). Same as S91.6-0.
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 127
MIB Information: hdviCfgITGRxGainAtten
1.3.6.1.4.1.429.1.29.1.1.1.8
mandatory read-write
Description: This object represents whether the ITGRxLevel represents gain or attenuation. 0 means gain and 1 means attenuation. Same as S92.7.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = gain
(2) = attenuation
MIB Information: hdviCfgITGRxGain
1.3.6.1.4.1.429.1.29.1.1.1.9
mandatory read-write
Description: This object represents the gain/attenuation level(in dB)to be applied to the incoming PCM signal. This level represents the amount of gain if ITGTxGainAttenuation is set to Gain(0). This level represents the amount of attenuation if ITGTxGainAttenuation is set to Attenuation(1).
Settings: INTEGER
Syntax Ref. Type: RANGE
0 = 127
MIB Information: hdviCfgEchoCancellerLen
1.3.6.1.4.1.429.1.29.1.1.1.10
mandatory read-write
Description: this object represents the length of the line echo canceller tail in mS where 0 means 8 ms1 means 16ms etc. Same as S93.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = t8ms
(2) = t16ms
(3) = t32ms
(4) = t64ms
(5) = t128ms
MIB Information: hdviCfgEchoCancellerDisable
1.3.6.1.4.1.429.1.29.1.1.1.11
obsolete read-write
Description: Disables echo canceller for voice calls. Note: If a data or fax call is detected when G.711 codec is used the echo canceller is automatically disabled. This object is obsolete and is now managed through hdviCfgEchoCanceller.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: hdviCfgEchoCancellerNLPDisable
1.3.6.1.4.1.429.1.29.1.1.1.12
obsolete read-write
Description: Disables Linear Processing in the Echo Canceller.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: hdviCfgEchoCancellerRTDDisable
1.3.6.1.4.1.429.1.29.1.1.1.13
mandatory read-write
Description: Disables round trip delay compensation in the LEC.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = disable
(2) = enable
MIB Information: hdviCfgITGSuppressionThreshold
1.3.6.1.4.1.429.1.29.1.1.1.14
mandatory read-write
Description: Sets Silence Suppression Threshold. Silence is detected if the current energy is less than noise level plus the threshold. The threshold is in dB.
Settings: INTEGER
Syntax Ref. Type: RANGE
6 = 11
MIB Information: hdviCfgEchoCancellerNLP
1.3.6.1.4.1.429.1.29.1.1.1.15
mandatory read-write
Description: Enables linear Processing in the Echo Canceller.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = enable
(2) = disable
0 = 120
MIB Information: hdviCfgEffectiveFrameLossRate
1.3.6.1.4.1.429.1.29.1.1.1.17
mandatory read-write
Description: This QoS parameter is calculated at the end of a call using the following equation: ToPSTNEffectiveFrameLoss/ToPSTNTotalExpectedAudioFrames.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = frameLossRate-001
(2) = frameLossRate-005
(3) = frameLossRate-010
MIB Information: hdviCfgMaxJitterCompensation
1.3.6.1.4.1.429.1.29.1.1.1.16
mandatory read-write
Description: Represents the average amount of delay introduced at the decoder for jitter compensation. Specified in 1mS increments. The HiPerDSP will map the value of this parameter to an integer number of audio packets that most closely approximates the specified jitter buffer size.Default=40
Settings: INTEGER
Syntax Ref. Type: RANGE
(4) = frameLossRate-015
(5) = frameLossRate-020
MIB Information: hdviCfgEchoCanceller
1.3.6.1.4.1.429.1.29.1.1.1.18
mandatory read-write
Description: Disables/enables echo canceller. In Auto-detect mode the operation of the LEC (on or off) is determined by G.168. In general the LEC is (on) for high speed data calls (V.34 x2 V.90) and (off) for low speed data fax and voice calls.
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = enable
(2) = disable
(3) = autoDetect
Copyright © 2000 3Com Corporation.