|
|
|
|
MIB Information: sdhAps
1.3.6.1.4.1.429.1.46.2
MIB Information: sdhApsTable
1.3.6.1.4.1.429.1.46.2.1
not-accessible
Description: The SDH Line Level APS Table.
MIB Information: sdhApsEntry
1.3.6.1.4.1.429.1.46.2.1.1
not-accessible
Description: An entry in the SDH Line Level Aps Table.
MIB Information: sdhApsIndex
1.3.6.1.4.1.429.1.46.2.1.1.1
mandatory read-only
Description: Index for the Aps Table at the SDH Line Level.
Settings: INTEGER
MIB Information: sdhApsMode
1.3.6.1.4.1.429.1.46.2.1.1.2
mandatory read-only
Description: This object specifies the state of APS mode. 0x0001=automatic mode 0x0002=lockout mode
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = automatic
(2) = lockout
MIB Information: sdhApsModeCmdResult
1.3.6.1.4.1.429.1.46.2.1.1.3
mandatory read-only
Description: This object specifies the result of APS mode order. 0x0001=normal0x0002=side-SBY order 0x0003=at mode change
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = normal
(2) = sideSbyOrder
(3) = atModeChange
MIB Information: sdhApsSndSelState
1.3.6.1.4.1.429.1.46.2.1.1.4
mandatory read-only
Description: This object specifies the state of APS send K1/K2 byte.0x0001=sending own-side k1/k2 value(APS-SND) 0x0002=sending other side K1/K2 value(APS-HLT)
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = ownSide
(2) = otherSide
MIB Information: sdhApsProtocolState
1.3.6.1.4.1.429.1.46.2.1.1.5
mandatory read-only
Description: This object specifies the state of APS protocol.0x0001=side-0:APS-MAIN side:1APS-RESERVE 0x0002=side-1:APS-MAIN side-1:APS-MAIN side-0:APS-RESERVE
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = side0
(2) = side1
MIB Information: sdhApsSwitchState
1.3.6.1.4.1.429.1.46.2.1.1.6
mandatory read-only
Description: This object specifies the state of APS Switching.0x0001=No Switching 0x0002=compulsive switch by remote module order0x0003=SF switching by remote module order0x0004=SD switching by remote moidule order0x0005=compulsive switch by local order0x0006=SF Switch by self order0x0007=SD switching by self order0x0008=compulsive switching at once0x0009=SF switching at once0x000A=SD switching at once
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = noSwitching
(2) = remoteCompulsiveSwitching
(3) = remoteSwitchingSF
(4) = remoteSwithingSD
(5) = localCompulsiveSwitching
(6) = selfSwitchingSF
(7) = selfSwitchingSD
(8) = atOnceCompulsiveSwitching
(9) = atOnceSwitchingSF
(10) = atOnceSwitchingSD
MIB Information: sdhApsCompSwitchResult
1.3.6.1.4.1.429.1.46.2.1.1.7
mandatory read-only
Description: This object specifies the result of the compulsive switch order.0x0001=Normal 0x0002=side-SBY order0x0003=the own system fails in switching0x0004=Compulsive switching0x0005=disobedience to order0x0006=no-switchingby remote module
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = normal
(2) = sideSbyOrder
(3) = ownSystemFailsinSwitching
(4) = compulsiveSwitching
(5) = disobedienceToTheOrder
(6) = noSwitchingByRemoteModule
MIB Information: sdhApsDuplexModeOrder
1.3.6.1.4.1.429.1.46.2.1.1.8
mandatory read-write
Description: This object specifies DRIVE MODE. 0x0001=simplex 0x0002=Duplex
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = simplex
(2) = duplex
MIB Information: sdhApsCmdForceRequest
1.3.6.1.4.1.429.1.46.2.1.1.9
mandatory read-write
Description: This object contains the value that identifies the command being requested for APS switch mode. 0x0001=Automatic mode 0x0002=Lock Mode
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = automatic
(2) = lockout
MIB Information: sdhApsCmdForce
1.3.6.1.4.1.429.1.46.2.1.1.10
mandatory read-only
Description: This object contains the value that identifies the command is ineffect for APS switch. 0x0001=automatic mode 0x0002=Lock mode
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = automatic
(2) = lockout
MIB Information: sdhApsChgNameTimerOrder
1.3.6.1.4.1.429.1.46.2.1.1.11
mandatory read-write
Description: This object contains the value thatfor protection time for recovery. 0x0001=5 Minute 0x0002=30 second
Settings: INTEGER
Syntax Ref. Type: ENUM
(1) = fiveMinutes
(2) = thirtySeconds
Copyright © 2000 3Com Corporation.