|
|
|
|
MIB Information: sdhState
1.3.6.1.4.1.429.1.46.7
MIB Information: sdhStateTable
1.3.6.1.4.1.429.1.46.7.1
not-accessible
Description: The SDH Line Level State Table.
MIB Information: sdhStateEntry
1.3.6.1.4.1.429.1.46.7.1.1
not-accessible
Description: An entry in the SDH Line Level State Table.
MIB Information: sdhStateIndex
1.3.6.1.4.1.429.1.46.7.1.1.1
mandatory read-only
Description: Index for the State Table at the SDH Line Level.
Settings: INTEGER
MIB Information: sdhStateApsSwitch
1.3.6.1.4.1.429.1.46.7.1.1.2
mandatory read-only
Description: Setected state of APS (a) TRAP ID 0x08 = sdhApsSwitchTE(b) state 0x000000 = no-information 0x000001 = ACT-->SBY change 0x000002 = SBY-->ACT change 0x000003 = SBY-->OUS change 0x000004 = ACT-->OUS change 0x000005 = OUS-->SBY change
Settings: INTEGER
MIB Information: sdhStateTransNameChg
1.3.6.1.4.1.429.1.46.7.1.1.3
mandatory read-only
Description: Notication of transmission name change (a) TRAP ID 0x09 = sdhTransNameChgTE(b) contents 0x000000 = no-information 0x000001 = side-0 APS-MAIN 0x000002 = side-1 APS-MAIN
Settings: INTEGER
MIB Information: sdhStateApsCableFault
1.3.6.1.4.1.429.1.46.7.1.1.4
mandatory read-only
Description: Failure state of APS cable(a) TRAP ID 0x0A = sdhApsCableFaultTE(b) contents 0x000000 = no-information 0x000001 = recovery 0x000002 = detect
Settings: INTEGER
MIB Information: sdhStateOthSidePowerOff
1.3.6.1.4.1.429.1.46.7.1.1.5
mandatory read-only
Description: Power supply failure of card in the other-side(a) TRAP ID 0x0B = sdhOthSidePowerOffTE(b) contents 0x000000 = no-information 0x000001 = recovery 0x000002 = detect
Settings: INTEGER
MIB Information: sdhStateOthSideCardFault
1.3.6.1.4.1.429.1.46.7.1.1.6
mandatory read-only
Description: Heart Beat check in the other-side card(a) TRAP ID 0x0C = sdhOthSideCardFaultTE(b) contents 0x000000 = no-information 0x000001 = recovery 0x000002 = detect ( no reply )
Settings: INTEGER
MIB Information: sdhStateEquipFailure
1.3.6.1.4.1.429.1.46.7.1.1.7
mandatory read-only
Description: Content of Equipment Failure (a) TRAP ID 0x0D = sdhEquipFailureTE(b) contents 0x000000 = no-information 0x000001 = recovery 0x000002 = detect
Settings: INTEGER
MIB Information: sdhStateSectionAlarm
1.3.6.1.4.1.429.1.46.7.1.1.8
mandatory read-only
Description: Content of Section alarm (a) TRAP ID 0x01 = sdhSectionOrderTE(b) where the alarm was detected 0x1 = receiver side 0x2 = send side <c) case of the alarm where the alarm was detected = 0x1 0x1 = LOS 0x2 = LOF 0x3 = MS-AIS 0x4 = SD(B1) 0x5 = SD(B2) where the alarm was detected = 0x2 0x1= TF 0x2 = MS-RDI(d) rating of the alarm 0x1 = Clear 0x2 = Warning 0x3 = Minor 0x4 = Major (e) REP-ID 0x000 --- 0x03F = 0 --- 63
Settings: INTEGER
Copyright © 2000 3Com Corporation.